Taylor Horizon 8752 Скачать руководство пользователя страница 5

Страница: 5 / 70

Models 8752 & 8756 with Horizon

Pump

To the Installer

Section 1

To the Installer

The following are general installation instructions. For

complete installation details, please see the check out

card.

Installer Safety

In all areas of the world, equipment should be

installed in accordance with existing local codes.

Please contact your local authorities if you have any

questions.

Care should be taken to ensure that all basic safety

practices are followed during the installation and

servicing activities related to the installation and

service of Taylor equipment.

Only authorized Taylor service personnel

should perform installation and repairs on

the equipment.

Authorized service personnel should consult

OSHA Standard 29CFRI910.147 or the

applicable code of the local area for the

industry standards on lockout/tagout

procedures before beginning any installation

or repairs.

Authorized service personnel must ensure

that the proper PPE is available and worn

when required during installation and

service.

Authorized service personnel must remove

all metal jewelry, rings, and watches before

working on electrical equipment.

The main power supply(s) to the freezer must

be disconnected prior to performing any repairs.

Failure to follow this instruction may result in personal

injury or death from electrical shock or hazardous

moving parts as well as poor performance or damage

to the equipment.

Note: All repairs must be performed by an

authorized Taylor Service Technician.

This unit has many sharp edges that can

cause severe injuries.

Site Preparation

Review the area the unit is to be installed in before

uncrating the unit making sure that all possible

hazards the user or equipment may come into have

been addressed.

For Indoor Use Only:

This unit is designed to operate

indoors, under normal ambient temperatures of 70

- 75

F (21

- 24

C). The freezer has successfully

performed in high ambient temperatures of 104

(40

C) at reduced capacities.

This unit must

NOT

be installed in an area

where a water jet or hose can be used.

NEVER

use a

water jet or hose to rinse or clean the unit. Failure to

follow this instruction may result in electrocution.

This unit must be installed on a level surface

to avoid the hazard of tipping. Extreme care should be

taken in moving this equipment for any reason. Two or

more persons are required to safely move this unit.

Failure to comply may result in personal injury or

equipment damage.

Uncrate the unit and inspect it for damage. Report any

damage to your Taylor Distributor.

This piece of equipment is made in the USA and has

USA sizes of hardware. All metric conversions are

approximate and vary in size.

Air Cooled Units

DO NOT

obstruct air intake and discharge openings:

Air cooled units require a minimum of 3” (76 mm) of

clearance around

all

sides of the freezer and 12” (305

mm) on top to allow for adequate air flow across the

condenser(s). Failure to allow adequate clearance can

reduce the refrigeration capacity of the freezer and

possibly cause permanent damage to the compressor.

Содержание Horizon 8752







































































Результаты поиска

Содержание Horizon 8752

Отзывы:

Похожие инструкции для Horizon 8752

Бренды по названию

Популярные бренды

Taylor Horizon 8752, Руководство по эксплуатации

Результаты поиска

Содержание Horizon 8752

Отзывы:

Похожие инструкции для Horizon 8752

Бренды по названию

Популярные бренды