manualshive.com logo in svg

Taylor C832, Руководство по обслуживанию

Поделиться
Скачать
Taylor C832 Скачать руководство пользователя страница 66

 60

Controls and Systems

McDonald's Intelligap Grills

Model C835 & C845 Gas Connections

To ensure proper operation, the Model C835 and
C845 gas grills require a minimum pipe size of 1
inch (25 mm).  For propane gas, the next lower size
can be used. If in doubt, contact the local gas
company.

The grill must be connected to the existing gas
supply lines with the hose assembly included in the
accessory package.

 All gas line connections and plumbing

must be inspected for leaks by using an electric
leak detector or a soap solution.

Gas Regulator Inspection

Step 1

 

Disconnect all power to the grill.

 Failure

to follow this instruction may result in electrical
shock.

Step 2

Turn off all gas supply.

 Failure to comply

can result in a fire hazard.

Step 3

Remove the MPT plug from the gas manifold.

Step 4

Install a barbed fitting.

Step 5

Connect a water column pressure gauge to the gas
manifold.

Step 6

Connect the power and gas supply.

Step 7

Turn on the grill.

Step 8

Turn on each heating zone, one at a time.

Step 9

After all heat zones are turned on, verify the gas
regulator settings:

Domestic:

Regulator Setting

Tolerance

Natural  Gas ‐ 3.5” w.c.

3.2 - 3.8

Propane Gas ‐ 10.5” w.c.

9.5 - 11.5

Note:  Domestic gas regulators must NOT be
adjusted.

 If the pressure adjustment deviates from

the tolerance range, the valve must be replaced.

International:

See Figure 44 on page  61.

IMPORTANT: Regulators should be inspected
separately.

Step 10

Remove all power, turn off the gas supply, and
re‐install the MPT plug, using an approved sealant.

Orifice Size

C835 Domestic:

Natural Gas

34

Propane Gas

52

C845 Domestic:

Natural Gas

40

Propane Gas

53

C835 & C845 International:

See Figure 44 on page  61.

Содержание C832




























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды