Taylor C832 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 219

Taylor C832 Скачать руководство пользователя страница 42

36

Controls and Systems

McDonald's Intelligap Grills

The set point for the grill is 425°F (218°C) for the
upper platens and 375°F (191°C) for the lower cook
surface. The grill will begin the daily auto-leveling
procedures once the grill is at 400°F (204°C) for the
upper platens and 325°F (163°C) for the lower cook
surface.

The dots on the lower cook surface indicate where
the thermocouples are located.

Step 1

Once you have entered the Service Passcode

(see page 23), press the

key until the screen

displays “SYSTEM SETUP.”

PRESS ENTER FOR

SYSTEM SETUP

Step 2

Press the

key to accept the selection.

Upon entering SYSTEM SET UP, the following
screen will display.

PROBE CALIBRATION

TOP BACK +00 424

Step 3

Place a pyrometer surface probe in the center of the
selected heat zone.

Step 4

If the displayed temperature on the controller is
more than 5°F/3°C different from the pyrometer

surface probe display, press the

key to

increase the temperature or the

key to

decrease the temperature to match the displayed
temperatures.

Note:

The set of numbers that follow the zone

name represent the previous calibration adjustment.

Step 5

To calibrate the next zone, use the

key to

move to the next zone.

Step 6

Once the calibration is complete, press the
key to save all changes.

Step 7

Press the

key to return to the AM/PM AUTO

Mode, or allow it to time-out after 3-5 seconds.

Display Temperature in °F/°C

Step 1

From the SYSTEM SET UP menu, press the
key until the temperature display screen appears.

TEMPERATURE DISPLAY

FAHRENHEIT

Step 2

Pressing the

keys will alter the display

message between F and C to display the
temperature in degrees Fahrenheit or Celsius.

TEMPERATURE DISPLAY

CELSIUS

Step 3

Press the

key to save the changes.

«
...
40
41
42
43
44
...
»

Содержание C832




























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды