Taylor C722 Скачать руководство пользователя страница 46

Страница: 46 / 67

Model C722

Important: Operator Checklist

PROBLEM

PROBABLE CAUSE

REMEDY

PAGE

REF.

10. Excessive mix leakage

from the bottom of door
spout.

a. Bottom o-ring on draw

valve is improperly
lubricated or is worn.

a. Lubricate properly or

replace the o-ring.

11. Excessive mix leakage

into the drip pan.

a. The seal on drive shaft is

improperly lubricated or is
worn.

a. Lubricate properly or

replace the seal.

b. The seal is installed

inside-out on the drive
shaft.

b. Install correctly.

c. Inadequate lubrication of

the drive shaft.

c. Lubricate properly.

d. The drive shaft and beater

assembly work forward.

d. Call an authorized service

technician.

- - -

e. Worn rear shell bearing.

e. Call an authorized service

technician.

- - -

f. Gear box out of alignment.

f. Call an authorized service

technician.

- - -

12. The drive shaft is stuck in

the drive coupling.

a. Mix and lubricant collected

in drive coupling.

a. Brush clean the rear shell

bearing area regularly.

b. Rounded corners of drive

shaft, drive coupling, or
both.

b. Call an authorized service

technician.

- - -

c. Gear box is out of

alignment.

c. Call an authorized service

technician.

- - -

13. The freezing cylinder

walls are scored.

a. Missing or worn front

bearing.

a. Install or replace the front

bearing.

b. Broken freezer door baffle

rod.

b. Replace freezer door.

- - -

c. Broken beater pins.

c. Replace beater assembly.

d. Beater assembly is bent.

d. Replace beater assembly.

- - -

e. Gear box is out of

alignment.

e. Call an authorized service

technician.

- - -

Содержание C722




































































Результаты поиска

Содержание C722

Отзывы:

Taylor C722, Руководство по эксплуатации, Страница: 46 / 67

Результаты поиска

Содержание C722

Отзывы: