Taylor C722 Скачать руководство пользователя страница 45

Страница: 45 / 67

Model C722

Important: Operator Checklist

121004

PROBLEM

PROBABLE CAUSE

REMEDY

PAGE

REF.

3. The product is too soft.

a. Draw rate is set too fast.

a. Adjust draw rate:

5 to 7-1/2 oz. (142 g. to
213 g.) of product by
weight in 10 seconds.

4. The product is too thick.

a. Freezing cylinder not

primed correctly.

a. Drain the freezing cylinder

and reprime the machine.

b. Air/mix pump incorrectly

assembled.

b. Assemble and lubricate

according to instructions
in this manual.

c. The viscosity control is set

too cold.

c. Call an authorized service

technician.

- - -

d. Freeze-up in mix inlet

hole.

d. Call an authorized service

technician.

- - -

5. The mix in the hopper is

too warm.

a. Hopper cover is not in

position.

a. Clean and sanitize hopper

cover and place in
position.

b. Agitator is not installed.

b. Clean, sanitize, and install

the agitator.

c. The hopper temperature is

out of adjustment.

c. Call an authorized service

technician.

- - -

6. The mix in the hopper is

too cold.

a. The hopper temperature is

out of adjustment.

a. Call an authorized service

technician.

- - -

7. Mix Low and Mix Out

probes are not
functioning.

a. Milkstone build-up in the

hopper.

a. Clean hoppers thoroughly.

8. The mix pump will not

operate.

a. Pump motor control is out

on internal overload.

a. Turn power switch off.

Remove and clean mix
pump. Allow at least two
minutes for power switch
to remain off, for control to
reset. Once power is
restored, before installing
pump, press pump key
and verify pump shaft
rotates counter-clockwise.

Note:

If rotation is

clockwise, call authorized
service technician.

- - -

9. Product is collecting on

top of the freezer door.

a. The top o-ring on draw

valve is improperly
lubricated or is worn.

a. Lubricate properly or

replace the o-ring.

Содержание C722




































































Результаты поиска

Содержание C722

Отзывы:

Taylor C722, Руководство по эксплуатации, Страница: 45 / 67

Результаты поиска

Содержание C722

Отзывы: