manualshive.com logo in svg

Taylor C722, Руководство по эксплуатации, Страница: 38 / 67

Поделиться
Скачать
Taylor C722 Скачать руководство пользователя страница 38

34

Model C722

Operating Procedures

130503

Note:

If the agitator should stop turning during

normal operation, with

sanitized hands

, remove

agitator from agitator drive shaft housing and brush
clean with sanitizing solution. Install the agitator
back onto the agitator drive shaft housing.

Repeat these steps for the other side of the
machine.

Note: Be sure your hands are clean and
sanitized before proceeding with these
instructions.

Priming

Note: Use only FRESH MIX when priming the
freezer.

Step 1

Place an empty mix pail beneath the door spouts.
With the prime plug in the UP position, pour 2-1/2
gallons (9.5 liters) of FRESH mix into the mix hopper
and allow it to flow into the freezing cylinder.

Step 2

Open the draw valve to remove all sanitizing
solution. When only fresh mix is flowing, close the
draw valve.

Step 3

Once a steady stream of mix starts to flow from the
prime plug opening in the bottom of the freezer door,
push the prime plug down.

Figure 75

Step 4

When mix stops bubbling down into the freezing
cylinder, remove the cotter pin from the outlet fitting
of the mix pump. Insert the outlet end of the mix
feed tube into the mix inlet hole in the mix hopper.
Place the inlet end of the mix feed tube into the
outlet fitting of the mix pump. Secure with cotter pin.

Figure 76

Step 5

Select the AUTO symbol

.

Note:

The brush clean counter will start at this time.

Step 6

Fill the hopper with fresh mix and place the mix
hopper cover in position.

Repeat these steps for the other side of the
machine.

Manual Brush Cleaning

This Procedure Must Be Completed Every Day

ALWAYS FOLLOW LOCAL HEALTH CODES.

To disassemble the Model C722, the following items
will be needed:

S

Two cleaning and sanitizing pails

S

Sanitizer/Cleaner

S

Necessary brushes (provided with freezer)

S

Single service towels

Содержание C722




































































Отзывы:

Нет отзывов