Taylor C722 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 67

Taylor C722 Скачать руководство пользователя страница 31

27

Model C722

Operating Procedures

130425

Step 9

Slide the beater assembly the rest of the way into
the freezing cylinder.

Make sure the beater assembly is in position over
the drive shaft by turning the beater slightly until the
beater is properly seated. When in position, the
beater will not protrude beyond the front of the
freezing cylinder. (See Figure 45.)

Figure 45

Repeat these steps for the other side of the
machine.

Step 10

To assemble the freezer door, place the door
gaskets into the grooves on the back of the freezer
door. Do not lubricate the gaskets.

Figure 46

Step 11

Slide the front bearings over the baffle rods. The
flanged edges should be against the door.

DO NOT

lubricate the gaskets or front bearings.

Slide the two o-rings into the grooves on each prime
plug. Apply an even coat of Taylor Lube to the
o-rings and shafts.

Figure 47

Step 12

Insert the prime plugs into the holes in the top of the
freezer door, and push down.

Figure 48

«
...
29
30
31
32
33
...
»

Содержание C722




































































Отзывы:

Нет отзывов