Taylor C602 Скачать руководство пользователя страница 71

Страница: 71 / 114

Troubleshooting

Model C602

Shake Dispensing Mechanism Troubleshooting

(Cont’d.)

PROBLEM

CAUSE

REMEDY

4. Draw valve does not fully open

(long draw time).

a. The solenoid bumper screw is

loose.

a. Align the actuator place and

secure the bumper screw to the
solenoid plunger.

b. The draw solenoid is adjusted too

high.

b. Adjust the draw solenoid to the

proper height. (See page 55.)

5. Draw valve will not close.

a. The freezer door is improperly

installed.

a. Re-install the freezer door. Tighten

the hand screws in a criss-cross
pattern.

b. Improper lubrication of draw valve.

b. Lubricate according to instructions

in the Operator’s Manual.

c. Improper o-rings installed on the

draw valve.

c. Install the correct o-rings - part no.

020571-1 (F treated)

d. The dispensing mechanism is out

of alignment.

d. Re-align the dispensing

mechanism. (See page 54.)

e. The draw valve is binding in the

freezer door.

e. Replace the defective component.

f. The solenoid plunger is binding in

the coil body.

f. Replace the solenoid.

Содержание C602



















































































































Результаты поиска

Содержание C602

Отзывы:

Похожие инструкции для C602

Бренды по названию

Популярные бренды

Taylor C602, Руководство по обслуживанию

Результаты поиска

Содержание C602

Отзывы:

Похожие инструкции для C602

Бренды по названию

Популярные бренды