Taylor C602 Скачать руководство пользователя страница 68

Страница: 68 / 114

Model C602

Troubleshooting

Peristaltic Syrup System Troubleshooting

(Cont’d.)

PROBLEM

CAUSE

REMEDY

4. Flavor carry-over.

a. There is air in the syrup line.

a. Prime the syrup line.

b. The Whitespot Setting is incorrect.

b. Adjust the Whitespot Setting in the

Service Menu. Recommended
setting: 0.1 - 0.2 for standard

shakes and 0.4 for Triple Thick
Shakes.

c. The pump motor reverse time is

set too low.

c. Adjust the pump motor reverse

time in the Syrup Motor Setup
menu.

d. The reverse relay does not reverse

the pump motor rotation when the
syrup flow is stopped.

d. Check the syrup reverse relay

voltage supply. (The relay is
energized to reverse the pump

motor rotation.)

e. The duckbill valve is defective.

e. Replace the duckbill valve.

f. The draw solenoid does not keep

the draw valve raised.

f. See Shake Dispensing

Mechanism Troubleshooting on
page 67.

5. Shake is not blended correctly.

a. The spinner height is set too low.

a. Adjust to 1/32” inside the door

spout.

b. Shake temperature is set too cold /

is too thick.

b. Correct the temperature of a

finished chocolate shake:
Standard shake = 24-26°F (4.4 -

3.3°C). Triple Thick Shake =
22.5°F (-5.8°C).

c. Syrup calibration is not in

specification.

c. Calibrate the syrup.

6. Unable to calibrate the syrup

within specification.

a. The weekly syrup line cleaning

was not performed.

a. Clean and sanitize the syrup lines.

b. The pump tube is worn.

b. Replace the tube.

c. There’s an obstruction in the syrup

line.

c. Clean out and replace the line if

necessary.

d. The syrup is too cold.

d. Stage the syrups near the

machine.

e. There is an air leak on the intake

side of the syrup line/pick up tube.

e. Find the leak and repair/replace.

f. Incorrect Syrup Calibration Setting. f. Adjust the Syrup Cal setting in the

Service menu: 5.0 seconds for
standard shakes and 7.0 seconds

for Triple Thick Shakes.

g. The syrup fills the cup too fast to

accurately calibrate.

g. Adjust the motor speed setting

slower in the Syrup Motor Setup
menu.

Содержание C602



















































































































Результаты поиска

Содержание C602

Отзывы:

Похожие инструкции для C602

Бренды по названию

Популярные бренды

Taylor C602, Руководство по обслуживанию

Результаты поиска

Содержание C602

Отзывы:

Похожие инструкции для C602

Бренды по названию

Популярные бренды