manualshive.com logo in svg

Taylor 390, Руководство пользователя, Страница: 16 / 16

Поделиться
Скачать
Taylor 390 Скачать руководство пользователя страница 16

4.8 BEVERAGE EQUIPMENT:   

   

 

 

                            

 

 

4.8.6.3 Iced Cappuccino Machine 

16 

Issue Date: February 21, 2008 

Taylor 390 

 

Last Modified: October 31, 2008 

Monthly Maintenance: 

 

1.  Check rear shell bearing for signs of wear 

(excessive mix leakage in the drip pan) and be 
certain it is properly cleaned.  

2.  Dispose of O-Rings or seals that are worn, torn or fit 

too loosely and replace with new ones. 
 

Semi -Annual Maintenance: 

 

1.  Tune-up Kits are available and all parts should be installed twice annually 

(Before Peak Season - March and End of Season - October). 

 

390

 Tune-Up Kit

 

Part Description 

Quantity 

TDL #78116  

Front Bearing 2 1/2" Inside Diameter 

1 

x 

Guide Bearing 13/16" Long 

1 

x 

Gasket -Door 5.109"ID x 5.630OD 

1 

x 

O-Ring .291 ID x .080W 

1 

x 

O-Ring 7/8 OD x .139W 

1 

x 

O-Ring 1"OD x .139W 

2 

x 

Drive Shaft Boot Seal 

1 

x 

Tool - O-Ring Removal 

1 

x 

Scraper Blade 

2 

x 

O-Ring .563 OD x .070W 

1 

x 

Lubricant 1 

x 

 
NOTE

: In order to maximize performance and efficiency of the unit, all parts 

should be replaced three times annually even if they do not appear to be 
worn, torn or damaged. 

 

2.  Rotate scraper blades to allow both sides of the knife edge to wear evenly. 

This will contribute to self-sharpening and help maintain fast efficient freezing.  

NOTE

: Scraper blades must be replaced semi-annually, but should be 

carefully inspected for nicks or other damage after three months if the unit is 
used in high volume stores. 

3.  Carefully inspect the bristles on all cleaning brushes (replace if necessary).

 

NOTE

: All brushes should be replaced on an annual basis. 

 

 

 

Please contact TFI Canada Toll Free at 1-800-387-2529 if 

you have any questions or concerns relating to this product. 

Press #1 for Parts and #2 for Service 

 

All manuals and user guides at all-guides.com

all-guides.com

Содержание 390

















Отзывы:

Нет отзывов