manualshive.com logo in svg

Taylor 390, Руководство пользователя, Страница: 11 / 16

Поделиться
Скачать
Taylor 390 Скачать руководство пользователя страница 11

4.8 BEVERAGE EQUIPMENT:   

   

 

 

                            

 

 

4.8.6.3 Iced Cappuccino Machine 

11 

Issue Date: February 21, 2008 

Taylor 390 

 

Last Modified: October 31, 2008 

17. To remove the scraper blade from the metal scraper blade clip, 

gently

 tap the 

tapered end of the scraper blade on the edge of the sink.  This will loosen the 
metal clip for easy removal and improved cleaning. 

     

     

 

18. Thoroughly brush clean all disassembled parts making sure all lubricant and 

product residue is removed.  Place all the cleaned parts on a clean parts tray 
or a clean and dry surface to air dry. 

NOTE

: O-Rings should be inspected on a weekly basis for cracks, nicks or 

tears.  Always replace any parts which are damaged before reassembly. 

 

ASSEMBLY

: 

1.  To reassemble the beater drive shaft, slide the beater shaft seal onto the 

beater shaft until it snaps into place and then slide the O-Ring into the first 
groove.  Lubricate the groove, O-Ring and beater seal (as shown below). 

 

NOTE

: 

DO NOT 

lubricate the square end of the beater drive shaft.  Fill the 

inside portion of the seal with 1/4” more lubricant and evenly lubricate the flat 
side of the seal that fits onto the rear shell bearing.  

 

     

     

 

2.  Install the drive shaft into the freezing cylinder, square end first, and into the 

rear shell bearing until the seal fits securely over the rear shell bearing.  Be 
certain the drive shaft fits into the drive coupling without binding.

  

NOTE

: Use your index finger to wipe off any excess lubricant at the contact 

point of the shaft seal and rear freezing cylinder 

     

     

 

NO LUBE 

Square 

End 

All manuals and user guides at all-guides.com

all-guides.com

Содержание 390

















Отзывы:

Нет отзывов