Taurus Titanium BT-SM 2534 DUAL, Инструкция по эксплуатации

Страница: 14 / 20

AFTER SALES SUPPORT
1300 922 271 service.australia@einhell.com
14 MODEL NUMBER: BT-SM 2534 DUAL, 12/11
7.3 Precision adjustment for 90° straight cut
(Figs. 1, 6-8)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking screw (21) and move the machine
head (4) all the way to the right using the handle (1).
•
Place the 90° angular stop (a) between the saw blade
(7) and the turntable (17).
•
Adjust the adjusting screw (29) using a Phillips head
screw driver until the angle between the saw blade (7)
and the turntable (17) equals 90°.
•
Finally check the position of the pointer (20) on
the scale (19). If necessary, undo the pointer (20)
with a Phillips screwdriver, set it to the 0° position
on the scale (19) and retighten the retainer screw.
•
No stop angle included.
7.4 Precision adjustment for 45° bevel cut (Figs. 1, 7, 9)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking screw (21) and move the machine
head (4) all the way to the left using the handle (1),
until it coincides at 45°.
•
Place the 45° stop angle (b) between the blade (7)
and the turntable. (17)
•
Adjust the adjusting screw (30) so that the angle
between the blade (7) and the turntable (17) equals
exactly 45°.
•
No stop angle included.
7.5 Adjusting the bevel angle (Figs. 2 & 13)
•
Undo the locking screw (21).
•
Hold the machine head (4) by the handle (1).
•
After pulling the button (33), the machine head
can be tipped infinitely as well as to several
locking points.
•
Angles to the left: 0-45°
•
Angles to the right: 0-45°
•
Re-tighten the locking screw (21).
7.6 Adjusting the removable fence (Figs. 1, 10-14)
•
Important! This saw is equipped with a removable
fence (9) which is screwed to the fixed fence (11).
•
For bevel cuts and compound mitre cuts with the saw
head tilted to the right, the removeable fence (9) must
be removed completely. Important! In this case the
maximum permissible workpiece height is reduced
(see 6. Technical data).
•
To remove the fence (9) loosen the two screws (e)
as shown in Fig. 10 and lift up the fence (9).
•
Always fasten the removable fence (9) on the
equipment again after you have completed your work.
•
The fence must always remain together with
the equipment. A removed fence will impair the
operational safety of the equipment.
8. FUNCTIONS
8.1 Straight cut 90° (Figs. 1-3, 11)
For cutting widths up to approx. 100 mm it is possible
to fix the saw’s sliding function with the slide lock screw
(24) in rear position. If the cutting width exceeds 100 mm,
you must ensure that the slide lock screw (24) is slackened
and that the machine head (4) can be moved.
•
Move the machine head (4) to its upper position.
•
Use the handle (1) to push back the machine head (4)
and fix it in this position if required (depends on the
cutting width).
•
Place the piece of wood to be cut at the fixed fence (11)
and on the turntable (17).
•
Lock the material with the clamping device (8) on the
fixed saw table (18) to prevent the material from
moving during the cutting operation.
•
Push down the release lever (3) to release the
machine head (4).
•
Press the ON/OFF switch (2) to start the motor.
•
With the slide guide (23) fixed in place: Use the
handle (1) to move the machine head (4) steadily
and with light pressure downwards until the saw
blade (7) has completely cut through the workpiece.
•
With the slide guide (23) not fixed in place: Pull the
machine head (4) all the way to the front and then use
the handle to move it downwards steadily and with
light pressure. Now push the machine head (4) slowly
and steadily to the very back until the saw blade (7)
has completely cut through the workpiece.
•
When the cutting operation is completed, move the
machine head (4) back to its upper (home) position
and release the ON/OFF switch (2).
Important! The integral resetting springs will
automatically lift the machine head. Do not simply let
go of the handle (1) after cutting, but allow the machine
head (4) to rise slowly, applying slight counter pressure
as it does so.
8.2 Mitre cut 0° - 45° (Figs. 1-3, 12)
The sliding mitre saw can be used to make mitre cuts
of 0°- 45° to the left and 0° - 45° to the right in relation
to the fence.
•
Release the turntable (17) by turning the locking
screw (14) into an anti-clockwise direction and pull
the release device (37).
•
Turn the turntable (17) and pointer (15) to the desired
angular setting on the scale (16) and lock into place
with the locking screw (14). The saw has locking
positions at angles of - 45°, -31.6°, -22.5°, -15°, 0°,
15°, 22.5°, 31.6° and 45°, at which the turntable (17)
audibly clicks into position.
•
Retighten the locking screw (14) to secure the
turntable (17) in place.
•
Cut as described in section 8.1.