Taurus BT-CK 18 2B-1.5 Kit, Инструкция по эксплуатации

Страница: 22 / 40

21
After Sales Support EMAIL: service.australia@einhell.com TEL: 1300 922 271
lever is securely fastened.
5.5.4 Parallel stop (Figure 6/7)
•
The parallel stop (21) enables you to saw parallel lines.
• Loosen the locking lever for the parallel stop (7) on the
soleplate (9).
• To assemble, slide the parallel stop (21) into the guide (a)
on the soleplate (9) (see Figure 6)
• Set the required spacing and then tighten the locking
lever (7) again.
• Using the parallel stop: Position the parallel stop (21) flat
on the edge of the workpiece and start the cut.
Important! Carry out a trial cut in a piece of waste wood
5.6. OPERATION
Important. For safety reasons the hand-held circular saw
must not be operated with the Allen key (10) inserted in it.
5.6.1 Working with the hand-held circular saw
Important. Always remove the battery pack before doing
any work on the circular saw!
• Always hold the circular saw firmly.
• The swing guard hood (18) is pushed back automatically
by the workpiece.
• Do not use force! Push forwards gently and evenly with
the circular saw.
• The work piece should be on the left-hand side of the
circular saw so that the wide section of the support bench
supports its full area.
• If you are sawing down a line that has been drawn, guide
the circular saw along the corresponding notch.
• Clamp small pieces of wood securely before sawing them.
Never hold them with your hand.
• Always follow the safety instructions. Wear safety goggles.
• Do not use defective saw blades or blades that are
cracked or broken.
• Do not use any flanges / flange nuts whose bore hole is
larger or smaller than those in the saw blade.
• The saw blade must not be decelerated by hand or by
applying lateral pressure to the blade.
• The swing guard hood must not jam and must return to
its initial position after the operation has been completed.
• Before you use the circular saw, check the function of the
swing guard hood with the battery disconnected.
• Before you use the machine, ensure that the safety
equipment such as the swing guard hood, flanges and
adjustment devices are in working order and are correctly
adjusted and secure.
• The moving swing guard hood must not be fixed in the
retracted guard hood when the saw is in use.
5.6.2 Using the circular saw (Fig. 1a)
• Adjust the cutting depth, cutting angle and parallel stop
(see section 5.2, 5.3 and 5.4)
• Ensure that the ON/OFF switch (2) is not depressed. Push
on the battery pack.
• Do not switch on the circular saw until you have fitted a
saw blade.
• Place the soleplate (9) flat on the workpiece you wish
to saw. The saw blade must not be in contact with the
workpiece.
• Hold the circular saw firmly with both hands.
5.6.3 Switching ON/OFF (Fig. 1)
To switch on:
Press the locking button (3) and the ON/OFF switch (2) at the
same time
• Allow the saw blade to accelerate until it reaches full
speed. Then slowly move the saw blade along the cutting
line. Only exert gentle pressure on the saw blade as you
do so.
To switch off:
Release the locking button (3) and ON/OFF switch (2)
• If you release the ON/OFF switch (2) the equipment will
shut down automatically which means that it cannot
operate accidentally.
• Ensure that you do not cover or block the ventilation
openings whilst working with the tool.
• Do not slow down the saw blade after you switch it off by
pressing it sideways.
• Important! Do not put down the machine until the saw
blade has reached a complete standstill.
Important. Carry out a trial cut in a piece of waste wood
5.6.4 Changing the saw blade (Fig. 8-11)
Important. Always remove the battery pack before doing
any work on the circular saw!
• Only use saw blades of the same type as the saw blade
supplied with this circular saw. Ask your dealer for advice.
• To change the saw blade (15), use the Allen key (10)
supplied with the equipment. The Allen key (10) is stored
in the equipment housing. Pull the Allen key (10) out of
the housing when you need it. (See Fig. 8)
• Push back and secure the moving swing guard hood (18)
using the lever for the swing guard hood (17).
• Undo the screw to secure the saw blade (19) using the
Allen key (10).
• Remove the flange (20) and the saw blade (15) in a
downwards direction.
• Clean the flange (20) and insert the new saw blade. Pay
attention to the running direction (see arrow on the
guard hood and saw blade).
• Tighten the screw to secure the saw blade (19), check it