Taurus BT-CK 18 2B-1.5 Kit, Инструкция по эксплуатации

Страница: 21 / 40

20
After Sales Support EMAIL: service.australia@einhell.com TEL: 1300 922 271
Please note that our equipment has not been designed
for use in commercial, trade or industrial applications. Our
warranty will be voided if the machine is used in commercial,
trade or industrial businesses or for equivalent purposes.
5.4. TECHNICAL DATA
Voltage supply: 18V d.c.
Idling speed: 3600 rpm
Cutting depth at 90°: 41mm
Cutting depth at 45°: 25mm
Saw blade: Ø 138mm
Blade holder: Ø 10mm
Blade thickness: 1.2 mm
Weight: 2.5 kg
Sound and vibration
Sound and vibration values were measured in accordance
with EN 60745.
L
pA
sound pressure level 83 dB(A)
K
pA
uncertainty 3 dB
L
WA
sound power level 94 dB(A)
K
WA
uncertainty 3 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing. Total
vibration values (vector sum of three directions) determined
in accordance with EN 60745.
Handle
Vibration emission value ah = 10.749 m/s
2
K uncertainty = 1.5 m/s
2
Additional handle
Vibration emission value ah = 8.259 m/s
2
K uncertainty = 1.5 m/s
2
Additional information for electric power tools
Warning!
The specified vibration value was established in accordance
with a standardized testing method. It may change according
to how the electric equipment is used and may exceed the
specified value in exceptional circumstances.
The specified vibration value can be used to compare the
equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a minimum.
• Only use appliances which are in perfect working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Residual risks
Even if you use this electric power tool in accordance with
instructions, certain residual risks cannot be rules out.
The following hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust mask is used.
2. Damage to hearing if no suitable ear protection is used.
3. Health damage caused by hand-arm vibrations if the
equipment is used over a prolonged period or is not
properly guided and maintained.
5.5. BEFORE STARTING THE
EQUIPMENT
Charge the battery pack with the charger supplied. An empty
battery pack requires a charging period of approximately 1
hour.
For more details about charging the battery pack please read
the operating instructions of the 1-hour charger.
Always remove the battery pack before making adjustments
to the equipment.
5.5.1 Mounting and removing the battery pack (Fig. 2/Item
12)
Mounting:
Push the battery pack (12) onto the equipment until it latches
in place.
Removing:
Press the pushlock button (13) and pull the battery pack (12)
out of the equipment.
5.5.2 Setting the cutting depth (Figure 3)
• Release the lever on the rear of the guard hood for
adjusting the cutting depth (11).
• Place the soleplate (9) flat on the surface of the workpiece
you wish to saw. Raise the saw until the saw blade (15) is
at the required cutting depth (a).
• Refasten the lever for adjusting the cutting depth (11).
Check the lever is securely fastened.
5.5.3 Miter stop (Figure 4/5)
• The preset standard angle between the soleplate (9) and
saw blade (15) is 90°. You can adjust this angle to carry out
angled cuts.
• Release the locking lever for miter setting (8) on the front
of the soleplate (9).
• You can now adjust the cutting angle to around 45°. Keep
an eye on the cutting angle scale (6) as you do so.
• Refasten the locking lever for miter setting (8). Check the