background image

7

Marchesan Implementos e Máquinas Agrícolas “TATU” S.A.

ROAT² 1700 / ROAT² 3400 / ROAT² 3400 TL

Transportation over truck or trailer

  Marchesan does not advise the equipment traffic on highways, because this 

practice involves serious risks in addition to being prohibited by the current 

existing traffic law. The transportation for long distances should be done on 

truck, trailer or others by following these safety guidelines:

• Use adequate ramps to load or unload the equipment. Do not make the loading 

on ditch banks, it can cause a serious accident.

• When lifting with a hoist, use the appropriate points to lift.

• Fasten the moving parts that may get loose and cause accidents.

• Underpin the equipment appropriately.

• Use chock blocks and safety chains to secure the equipment to the truck or 

trailer during the transport.

• Make sure the SMV (Slow Moving Vehicle) sign, and all the lights and reflectors 

that are required by the local highway and transport autorithies are in place, 

are clean and can be seen clearly by all overtaking and oncoming traffic.

• After 8 to 10 km transporting, please inspect the load condition. Repeat this 

procedure every 80 to 100 km. Give more attention when transporting the 

equipment on rough roads, slopes and other adverse conditions.

• Always be careful with the load height, especially when passing under electrical 

power lines, bridges and others.

• Check all laws and regulations regarding the height limits and load width while 

transporting the equipment on truck or trailer. If necessary use banners, lights 

and other devices in order to give adequate warning to the other drivers.

To the operator

Содержание ROAT2 1700

















































Отзывы: