©Copyright Task Force Tips, Inc. 2011-2013
LIG-012 April 9, 2013 Rev02
13
8.0 FIELD INSPECTION
TFT’s G-Force is designed and manufactured to be damage resistant and require minimal maintenance. However, as the primary
fi re fi ghting tool upon which your life depends, it should be treated accordingly.
Use with saltwater is permissible provided nozzle is thoroughly cleaned with fresh water after each use. The service life of the nozzle
may be shortened due to the effects of corrosion and is not covered under warranty.
WARNING
Nozzle must be inspected for proper operation and function according to the inspection
checklist on last page before each use. Any nozzle that fails inspection is dangerous to use and
must be repaired before using.
Performance tests shall be conducted on the G-Force nozzle after a repair, or anytime a problem is reported to verify operation in
accordance with TFT test procedures. Consult factory for the procedure that corresponds to the model and serial number of the
nozzle. Any equipment which fails the related test criteria should be removed from service immediately. Troubleshooting guides are
available with each test procedure or equipment can be returned to the factory for service and testing.
CAUTION
Any alterations to the nozzle and its markings could diminish safety and constitutes a misuse
of this product.
All Task Force Tip nozzles are factory lubricated with high quality silicone grease. This lubricant has excellent washout resistance
and long term performance. If your department has unusually hard or sandy water, the moving parts may be affected. Foam agents
and water additives contain soaps and chemicals that may break down the factory lubrication.
The moving parts of the nozzle should be checked on a regular basis for smooth and free operation, and signs of damage. IF THE
NOZZLE IS OPERATING CORRECTLY, THEN NO ADDITIONAL LUBRICATION IS NEEDED. Any nozzle that is not operating
correctly should be immediately removed from service and the problem corrected.
9.0 REPAIR
Factory service is available with repair time seldom exceeding one day in our facility. Factory-serviced nozzles are repaired by
experienced technicians to original specifi cations, fully wet tested, and promptly returned. Repair charges for non-warranty items
are minimal. Any returns should include a note as to the nature of the problem and whom to reach in case of questions.
Task Force Tips assumes no liability for damage to equipment or injury to personnel that is a result of user service.
Repair kits and repair parts are stocked for immediate shipment. Contact the factory or visit the web site at www.tft.com for parts
lists, exploded views, test procedures and trouble shooting guides.
10.0 COLOR CODED VALVE HANDLE AND PISTOL GRIP
The TFT G-FORCE with lever type valve handles are supplied with black valve handle covers and pistol grips. The handle covers
and pistol grips are available from TFT in various colors for those departments wishing to color code the nozzle to the discharge
controls. A colored handle cover set will be sent upon receipt of the warranty card by TFT. Your department’s name can also be
engraved on the covers (see warranty card for more information).
Handle covers are replaceable by removing the four screws that hold the handle covers in place. Use a 3/32” allen wrench when
replacing screws. Pistol grip is replaceable by following TFT instruction sheet LTT-108.
For standardization NFPA 1901 (A-4-9.3) recommends the following color code scheme:
Preconnect #1 or Bumper Jump Line
Preconnect or discharge #2
Preconnect or discharge #3
Preconnect or discharge #4
Preconnect or discharge #5
Preconnect or discharge #6
Preconnect or discharge #7
Foam Lines
Orange
Red
Yellow
White
Blue
Black
Green
Red w/ White border (Red/White)
Other Colors Available:
• Gray
• Pink
• Purple
• Tan
11.0 ANSWERS TO YOUR QUESTIONS
We appreciate the opportunity of serving you and making your job easier. If you have any problems or questions, our toll-free
“Hydraulics Hotline”, 800-348-2686, is normally available to you 24 hours a day, 7 days a week.
