Taramps MD8000.1 Скачать руководство пользователя страница 11

2 - POSITIVE POWER SUPPLY: 

Use 2/0 AWG cables direct from the positive battery terminal, with fuse or 

circuit breaker (390A), as close to it as possible.

In order for your amplifier to have the best performance, it is necessary to use all the power inputs. See 
example on the next page. We recommend that all cables have tinned ends for better electrical contact.

In case of power bus bar using, avoid tightening with extenders on the allen wrench, as excessive torque 
may break the the terminal.

1  -  Fans:

 This  amplifier  has  two  internal  ventilation  fans,  which  cannot  be  obstructed.  For  a  perfect 

operation, the amplifier must be installed in a dry and airy place. We recommend not embedding it, in 
order to ensure adequate ventilation.

3 - NEGATIVE POWER SUPPLY: 

Use 2/0 AWG cables as short as possible, connected to the negative 

battery pole.

Power supply connector 

10

ENGLISH

Indicates that the amplifier is turned on.

Blinking yellow LED according to music:

 Indicates that the amplifier is operating at the 

threshold of distortion. If the red LED also blinks, it indicates excessive distortion.

Short-circuit or impedance lower than that supported at output.

Flashing  yellow  LED:

  Excessive  temperature  (May  be  caused  by  obstruction  of  the 

internal fans, improper installation or poorly ventilated location).

Red LED steady on:

We recommend don’t turn off the amplifier, so that the cooling time will be shorter, 
through the ventilation of fans.

Supply voltage less than 9.5V.

RED LED flashes 2x:

Power supply voltage greater than 17V.

Blue LED steady on:

When the amplifier reaches the temperature of approximately 80°C (176°F), the thermal 
protection starts working, the audio is interrupted and the yellow LED will start flashing. 
The fans will be functioning, in order to cool down the components quickly. Only when 
the amplifier reaches a safe temperature level, the audio is released and the amplifier 
gets back to its normal functioning.

RED LED flashes 3x:

LEDS indicators & protection systems

POWER 

INPUT

1

1

2

3

3

2

Содержание MD8000.1















Отзывы: