2-ASSEMBLY
Connect flexible hose to elbow of the machine and tighten the clamp.Connect spray tube to flexible hose and tighten clamp-
2.Connect chemical hose-2 to inlet side of on-off tap and also chemical hose-1 to outlet side of on-off tap chemical hose-1 to
outlet side of on-off tap and dosage sleeve.Connect chemical hose to the holder and pressure hose to air outlet nipple as
shown in Fig.2.Place the tank strainer.Assemble spray nozzle to spray tube.To obtain wide or short angle spraying loosen
plastic nut and move the nozzle forth and back.
3. YAKITIN HAZIRLANMASI
Yakýtýn hazýrlanmasýnda 1. paragrafta anlatýlan güvenli kullaným kurallarýna uyunuz.
3. PREPARING THE FUEL
In the fuel preparation, apply the safety regulations indicated in paragraph 1.
TARAL iki zamanlý motor yaðý kullanýmýný tavsiye eder.
TARAL recommends two-cycle engine oil to be used.
3.1-YAKITIN BÝDON ile HAZIRLANMASI
1.Yakýtýnýzý yalnýz temiz kaplara boþaltýn ve aletin orjinal hunisini kullanýn. Süper benzin kullanmayýn. Kursunsuz benzin
kullanýn.
2.Tablo 1 'de verilen oranlarda yakýt yað karþýmýný hazýrlayýn.(Örnek 10 Lt. benzine 0.4 Lt. iki zamanlý motor yaðý
karýþtýrýn).
3.Karýþýmý hazýrladýktan sonra bidonu (Þek.3) 'deki gibi çalkalayýn.
4.Süzgeçli huni yardýmý ile karþýmý aletin yakýt deposuna doldurun.
3.1-PREPARING THE FUEL BY USING A TANK
1.Pour the fuel only in a clean container and use the original funnel of the device. Do not use super gasoline
.
Unleaded
gasoline is recommended.
2.Prepare the fuel by using fuel and oil in the ratios shown in table 1. (e.g. with 10 Lt. fuel, mix 0,4 Lt. two cycle engine oil.)
3.After preparing the mixture, shake the container. (Fig. 3)
4.By using a strainer funnel, fill the fuel tank with the mixture.
3.2- YAKITIN ÖLÇEK KABI ile HAZIRLANMASI
1.Eðer iki zamanlý motor yaðý kullanýyorsanýz ölçek kabýnýn içindeki 1:25 yazýsýna kadar yað doldurun.
2.Ölçek kabýnýn içine koyduðunuz yaðýn üzerine benzin dökerek kabý iþaretli yere kadar doldurun.
Ölçek kabýnýn üzerine süzgeçli huniyi geçirin.
3.Huninin aðzýný parmakla kapatarak iyice çalkalayýn (Þekil. 4)
4.Hazýrlanmýþ olan yakýtý huniyi çýkartmadan kabý çevirerek yakýt deposuna doldurun.
Not: Yakýt yað karýþýmýný kesinlikle direkt olarak yakýt deposu içinde hazýrlamayýn. Aksi taktirde
motorunuz zarar görebilir.
3.2-PREPARING THE FUEL BY USING A MEASURING CUP
1.If you are using two-cycle engine oil, fill the measuring cup up to the 1:25 sign.
2.Add gasoline to the oil that has already been put in the measuring cup and thus fill the cup up to the marked level.
3.Block the funnel with your finger and shake it well (Fig. 4).
4.Pour the prepared fuel into the fuel tank while keeping the funnel on the cup.
Note: Never prepare the fuel oil mixture in the fuel tank. The engine can be damaged.
2 zamanlý
motor
yaðý/2cycle
engine oil
Benzin/Fuel
(lt)
1:25
% 4
5
0.200
10
0.400
15
0.600
20
0.800
25
1.000
Tablo 1(Table 1)
Þekil.3(Figure.3)
(6)
Þekil.4
(Figure.4)
