Tapco Windy SP PORT-O-BRAKE Скачать руководство пользователя страница 11

Страница: 11 / 11

REPLACING THE SHOE CASTING

Remove Hex Screws from

Back of Shoe Casting

Remove the four (4) Hex Head Screws

holding the Shoe Casting to the Bottom

rails front and back.

Open Brake

Move Locking Handle to right.

Remove Top Yoke Pin

With Brake unlocked remove Cotter

Pin from Top Yoke Pin and disengage

handle.

Remove Sliding Bar

Grasp and pull Sliding Bar to the right

and remove.

Tools needed: socket wrench with 7/16” socket, Phillips screwdriver

Remove Hex Head Screws

Holding Clamping Bar

This will allow you to reach ﬂat head

screws holding Fixed Hinge.

TAPCO PRODUCTS COMPANY

Item #11102

T0069-L 9/03

Remove Pivot Arm

Remove Pivot Arms and springs and

replace the Shoe Casting. When replac-

ing, make sure all fasteners are tight

Remove Hex Screws from

Front of Shoe Casting

Remove Flat Head Screws from Fixed

Hinge on the Shoe Casting to be re-

placed.

Содержание Windy SP PORT-O-BRAKE












Результаты поиска

Содержание Windy SP PORT-O-BRAKE

Отзывы:

Похожие инструкции для Windy SP PORT-O-BRAKE

Бренды по названию

Популярные бренды

Tapco Windy SP PORT-O-BRAKE, Руководство по эксплуатации

Результаты поиска

Содержание Windy SP PORT-O-BRAKE

Отзывы:

Похожие инструкции для Windy SP PORT-O-BRAKE

Бренды по названию

Популярные бренды