Tanaka TCH 22EAP2 50ST Скачать руководство пользователя страница 5

5

English

  Empty the fuel tank before storing the unit/

machine. It is recommended that the fuel be 

emptied after each use. If fuel is left in the tank, 

store so fuel will not leak.

  Store unit/machine and fuel in area where fuel 

vapors cannot reach sparks or open 

fl

 ames 

from water heaters, electric motors or switches, 

furnaces, etc.

 WARNING

  Fuel is easy to ignite or get explosion or 

inhale fumes, so that pay special attention 

when handling or 

fi

 lling fuel.

Cutting safety

  Do not cut any material other than plant hedge.

  Inspect the area to be cut before each use. 

Remove objects which can be thrown or become 

entangled.

 For respiratory protection, wear an aerosol 

protection mask when cutting the grass after 

insecticide is scattered.

 Keep others including children, animals, 

bystanders and helpers outside the 15 m hazard 

zone. Stop the engine immediately if you are 

approached.

  Hold the unit/machine 

fi

 rmly with both hands.

 Keep 

fi

 rm footing and balance. Do not over-

reach.

  Keep all parts of your body away from the mu

  er 

and cutting attachment when the engine is 

running.

  Keep cutting tool below shoulder level. NEVER 

operate unit from a ladder, while in a tree or from 

any unstable support.

  When relocating to a new work area, be sure to 

shut o

  the machine and ensure that all cutting  

attachments are stopped.

  Never place the machine on the ground when 

running.

  Always carry a 

fi

 rst-aid kit when operating any 

power equipment.

  Never start or run the engine inside a closed 

room or building and/or near the in

fl

 ammable 

liquid. Breathing exhaust fumes can kill.

Maintenance safety

 Maintain the unit/machine according to 

recommended procedures.

  Disconnect the spark plug before performing 

maintenance except for carburetor adjustments.

  Keep others away when making carburetor 

adjustments.

  Use only genuine Tanaka replacement parts as 

recommended by the manufacturer.

  When the hedge trimmer is stopped for servicing, 

inspection or storage, shut o

  the power source, 

disconnect the spark plug wire from the spark 

plug and make sure all moving parts have come 

to a stop.

 

Allow the hedge trimmer to cool before making 

any inspection, adjustment, etc.

Transport and storage

  Carry the unit/machine by hand with the engine 

stopped and the mu

  er away from your body.

  Allow the engine to cool, empty the fuel tank, 

and secure the unit/machine before storing or 

transporting in a vehicle.

  Empty the fuel tank before storing the unit/

machine. It is recommended that the fuel be 

emptied after each use. If fuel is left in the tank, 

store so fuel will not leak.

  Store unit/machine out of the reach of children.

  Clean and maintenance the unit carefully and 

store it in a dry place.

  Make sure engine switch is o

  when transporting 

or storing.

  When transporting in a vehicle or storage, cover 

blade with blade cover.

If situations occur which are not covered in this 

manual, take care and use common sense. Contact 

your Tanaka dealer if you need assistance. Pay 

special attention to statements preceded by the 

following words:

 WARNING

  Indicates a strong possibility of severe 

personal injury or loss of life, if instructions 

are not followed.

 CAUTION

 

Indicates a possibility of personal injury or 

equipment damage, if instructions are not 

followed.

NOTE

 

Helpful information for correct function and use.

 CAUTION

 

Do not disassemble the recoil starter. You 

may get a possibility of personal injury with 

recoil spring.

000Book̲TCH22EAP2(50ST)̲US.indb   5

000Book̲TCH22EAP2(50ST)̲US.indb   5

2014/12/16   10:15:36

2014/12/16   10:15:36

Содержание TCH 22EAP2 50ST





































Отзывы: