tams elektronik B-6 Скачать руководство пользователя

Страница: 41 / 48

ms elektronik

Booster B-6

9.2. Power supply unit

Manufacturer

MEAN WELL ENTERPRISE Co. Ltd.

Type designation

GSM160B24-R7B

Output

Output voltage

24 VDC

Rated current

6.67 A

Output current

0 – 6.67 A

Rated powerNennleistung

max. 160 watts

Input

Input voltage

80 ~ 264 VAC or 113 ~ 370 VDC

Frequency range

47 ~ 63Hz

Input current

90A / 115VAC or 110A / 230VAC

Efficiency

average: 93,5 %
at low load (10%): 87.5 %

Power consumption
at zero load

< 0,15 W

Protection

Protection

type

IP 22

Meaning: Predected against solid foreign bodies with diameter ≥ 12.5 mm and
access with a finger. Protection against falling dripping water when the
enclosure is tilted up to 15°.

Protection class

(= Protection class 2)

Overload

105 ~ 150% of the rated output power
Protection mode: Hiccup mode, i.e. automatic recovery after
elimination of fault condition

Overvoltage

105 ~ 135% of the rated output voltage
Protection mode: Switching off the output voltage, switching
on again for recovery

Overtemperature

Protection mode: Switching off the output voltage, switching
on again for recovery

Technical data | 41

Содержание B-6

















































Результаты поиска

Содержание B-6

Отзывы:

Похожие инструкции для B-6

Бренды по названию

Популярные бренды

tams elektronik B-6, Руководство пользователя

Результаты поиска

Содержание B-6

Отзывы:

Похожие инструкции для B-6

Бренды по названию

Популярные бренды