tams elektronik B-6 Скачать руководство пользователя

Страница: 39 / 48

ms elektronik

Booster B-6

9. Technical data

9.1. Booster B-6

Digital protocols

Data formats

Motorola-I and -II
DCC (according to NMRA and RCN standard)

m3 and mfx (limited to the control of mfx decoders)

Formats for the automatic
registration of vehicle
decoders

DCC-A
This function is not yet available (Status: 04/2023).

Feedback format

RailCom (RailCom cutout can be switched off)
integrated global RailCom detector

Interfaces

For the connection the digital
central unit or further
boosters

BiDiB (RJ45) or
DCC-compliant ("CDE"

For the connection of of a
BiDiB PC interface

BiDiB (RJ45)

Track output

Main track

Electrical properties

Power supply

24 volts direct current

Note: Only the power supply unit included in the scope of delivery is permitted
as power supply for the mc² including integrated booster!

Maximum output current

2.0 to 6.0 A
adjustable in 1 A steps

Current consumption

(without consumer)

max. 100 mA

Output voltage

8 to 22 volts digital voltage (regulated)
adjustable in 1 V steps

Output signal

symmetrical

Power consumption

max. 132 watts

Protection

Technical data | 39

Содержание B-6

















































Результаты поиска

Содержание B-6

Отзывы:

Похожие инструкции для B-6

Бренды по названию

Популярные бренды

tams elektronik B-6, Руководство пользователя

Результаты поиска

Содержание B-6

Отзывы:

Похожие инструкции для B-6

Бренды по названию

Популярные бренды