background image

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
B. TEMPERATURE CONVERSION       
 

This machine can display temperatures in either Celsius or Fahrenheit. To change to either one, simply 

press and hold the “TEMP/SET” arrow keys simultaneously. 

 

C. GUIDE PLATES 
 

This  machine  is  equipped  with  guide  plates  on  the  left  and  right  sides  of  the  feed  tray  for  proper 

alignment of materials to be laminated. Aside from being able to laminate 27" wide sheets one at a time, 

the user can also laminate up to two (2) 8.5"x11" prints simultaneously in either orientation by aligning 

them on each of the plates on both sides of the tray. 

 

D. REVERSE FUNCTION 
 

The machine is equipped with a reverse function. By pressing the “REVERSE” key, the machine will 

release the documents out from the front of the machine to prevent any jam or damage. 

 

E. MOUNTING FUNCTION     
 

1. This machine is equipped with a mounting function. The user can choose to mount prints or posters 

using up to 1/4” thick foam boards. 

a.  For  mounting  and  encapsulating  using  thermal  film,  simply  set  the  machine  up  for 

2-SIDED 

LAMINATION

. Line up the material evenly on a standard foam board and set the temperature

 

on the machine. 

 

b. For simultaneous mounting with 1-sided lamination using nylon, BOPP or even thermal film, set 

the machine up for 

1-SIDED LAMINATION

. Turn the bottom roller heater switch to the “off” 

position. Adjust the  temperature based on the thickness of the top roller film and make sure the 

Содержание Versalam 2700-P












Отзывы: