background image

 

Area of Rescue Command Unit

 

Installation Guide 

Model AOR-24 / Model AOR-32 

Product Revision 2.0

 

Page 

16

 of 

23

 

 

 

Rev. 3/8/2022

 

 

Copyright 2014-2022 Talk-A-Phone, LLC

 

• 7530 North Natchez Avenue • Niles, Illinois 60714 • Phone 773.539.1100 • [email protected] • www.talkaphone.com.  

 

All prices and specifications are subject to change without notice. Talk-A-Phone, Talkaphone, bAlert, Scream Alert, WEBS, and WEBS Contact are registered trademarks of 
Talk-A-Phone, LLC.  All rights reserved.  All other trademarks mentioned in this document or website are the property of their respective owners and does not imply or indicate 
any approval, endorsement, sponsorship, or affiliation with such owners unless such approval, endorsement, sponsorship, or affiliation is expressly indicated. 

Programming the AOR-CSE Stations 

Once each controller board has been programmed, the AOR-CSE Stations will need to be 
programmed individually. 

 

1. 

Calling into the AOR-CSE Station to enter programming mode. 

1.  To call from a remote phone, dial the telephone number of the phone line connected to 

a particular controller board.  Go to 

Step (3)

2.  To call from the command unit local phone, simply pick up the handset and press the 

line button (i.e. 

“BANK 1”

“BANK 2”

“BANK 3”

, or 

“BANK 4”

) corresponding to the 

appropriate bank of the AOR-CSE Station in question. 

3.  In either case, you will hear one (1) beep when the command unit is ready. 

4.  Enter the code to route to a specific AOR-CSE Station: 

* 4 [Select Port 1-8] *

 

There will be a short pause and then the AOR-CSE Station will answer with an open 

channel (i.e. microphone and speaker are active). 

 

2. 

Enter the security code:  

827827

 (or 

TAPTAP

3. 

Program the Primary Phone Number to dial:  

[0-20 digits for phone number] # 00

 

For local mode (i.e. calling the local phone), use 

any number

 as the phone number. 

For remote mode (i.e. calling an outside phone number), use the 

10-digit phone number 

of 

the answering point as the phone number. 

For mixed mode (i.e. alternating between local and remote), use the 

10-digit phone number 

of 

the answering point as the phone number. 

4. 

Program the Second Phone Number to dial:  

[0-20 digits for phone number] # 01

 

For local mode (i.e. calling the local phone), use 

any number

 as the phone number. 

For remote mode (i.e. calling an outside phone number), use the 

10-digit phone number

 of 

the answering point as the phone number. 

For mixed mode (i.e. alternating between local and remote), use the 

10-digit phone number

 of 

the answering point as the phone number. 

5. 

Set the call length, silence time out, ring count, and dial next number on busy:  

294521 # 18

 

See 

Timing/Dialing Options for the AOR-CSE Station (p.18)

 for further details. 

6. 

Recording a Location Message: 

IMPORTANT NOTE:

 

For the 

AOR-24 Command Unit

, there are three (3) controller boards

—you will need to repeat the 

programming process for the second and third banks/controller boards. 

For the 

AOR-32 Command Unit

, there are four (4) controller boards

—you will need to repeat the 

programming process for the second, third, and fourth banks/controller boards. 

NOTE: 

After each AOR-CSE Station programming code, a double-beep indicates the code has been 
accepted.  Four (4) beeps indicate an error

—re-enter the code again. 

Содержание AOR-24
























Отзывы: