Talkaphone AOR-16 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 39

background image

Area of Refuge Command Unit

Installation Instructions

Model AOR-24/AOR-32

Page

6

of

13

Rev. 10/15/2015

Copyright 2014 Talk-A-Phone Co.

• 7530 North Natchez Avenue • Niles, Illinois 60714 • Phone 773.539.1100 • [email protected] • www.talkaphone.com.

All prices and specifications are subject to change without notice.

Talk-A-Phone, Scream Alert, WEBS and WEBS Contact are registered trademarks of Talk-A-Phone Co. All rights reserved.

your other device picks up (or, if sharing with a standard telephone, be sure to
allow enough rings for the person answering the phone to pick up).

WARNING:

The other device sharing the line should never be emergency

equipment of any kind

22.

Once the correct configuration of for the

AOR-24/AOR-32

has been determined

and appropriately wired. Connect incoming 115-230 VAC 50-60Hz power wiring
to the power supply board located in the bottom compartment of the unit. The
LINE, NEUTRAL, and GROUND terminals are located on the left side of the
board.

WARNING:

The order in which 115-230 VAC 50-60Hz or backup

batteries is connected does not matter. However, once either the
batteries are connected OR the 115-230 VAC 50-60Hz line is
energized, THE UNIT WILL BECOME “HOT” ENERGIZED.

23.

Connect the backup batteries.
The  batteries  and  their  corresponding  connections  to  the  wiring  harness  are
labeled.    Starting  with  the  battery  that  is  labeled  with  the  numbers  3  and  4,
place  the  battery  on  the  lowest  battery  shelf  and  connect  the  matching  leads
from the wiring harness.

24.

Next locate the battery that is labeled with the numbers 5 and 6. Place this
battery on the second shelf from the bottom and connect the matching leads
from the wiring harness.

25.

Now locate the battery that is labeled with the numbers 7 and 8. Place this
battery on the third shelf from the bottom and connect the matching leads from
the wiring harness.

26.

Place the final battery, labeled with the numbers 9 and 10, on the top battery
shelf and connect the matching leads from the wiring harness.

27.

The  batteries  connect  to  the  power  supply  board  by  inserting  the  connector
onto  the  header  pins  located  on  the  bottom  right  of  the  power  supply  board
which  the  115-230 VAC  50-60Hz    power  supply  was  connected. Although  the
pins  are  polarized,  ensure  correct  polarity  when  connecting  the  backup
batteries. Red-positive & Black-negative.

«
...
17
18
19
20
21
...
»

Содержание AOR-16








































Отзывы:

Нет отзывов

Похожие инструкции для AOR-16

Бренд: Hanlong Страницы: 57

Бренд: TWIG Страницы: 4

Бренд: Philips Страницы: 2

Desktop 9850/52

Бренд: Philips Страницы: 24

Бренд: Aastra Страницы: 212

Бренд: Aastra Страницы: 228

Бренд: Mitel Страницы: 43

Бренд: Mitel Страницы: 51

Бренд: RCA Страницы: 25

IP Office H.323

Бренд: Avaya Страницы: 104

Бренд: Ubiquiti Страницы: 24

Бренд: Aastra Страницы: 53

Yealink SIP-T41P

Бренд: Yealink Страницы: 91

Бренд: Panasonic Страницы: 306

Бренд: Panasonic Страницы: 18

Бренд: Swissvoice Страницы: 6

Бренд: Grandstream Networks Страницы: 7

Бренд: Grandstream Networks Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды