Talkaphone AOR-16 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 39

background image

Area of Refuge Command Unit

Installation Instructions

Model AOR-24/AOR-32

Page

3

of

13

Rev. 10/15/2015

Copyright 2014 Talk-A-Phone Co.

• 7530 North Natchez Avenue • Niles, Illinois 60714 • Phone 773.539.1100 • [email protected] • www.talkaphone.com.

All prices and specifications are subject to change without notice.

Talk-A-Phone, Scream Alert, WEBS and WEBS Contact are registered trademarks of Talk-A-Phone Co. All rights reserved.

4.

Remove the telephone by sliding it upwards ½ [in] then lifting away from the
unit and out of the compartment. This will expose a mounting location within the
telephone compartment.

5.

After  installation,  reinstall  the  telephone  within  its  compartment  by  holding  the
phone  against  the  rear  surface  of  the  compartment  and  sliding  ½  [in]
downward.  If the phone will not  slide downward into locking position,  the  6-32
screws located behind the phone may need to be adjusted. Loosen the screws
¼  turn  by  hand  and  repeat  step  8.  Likewise,  if  the  telephone  slides  correctly
downward  but  does  not  feel  secure  in  place,  tighten  the  nuts  ¼  turn  by  hand
and repeat  step 8. Plug phone and power connections back into phone in  the
correct order.

6.

Remove the three (3) Phillips screws from the left side of the unit which secure
the hinged front cover shut.

7.

Carefully open the hinged front cover taking care there are no loose items
which may have shifted during transportation.

8.

The

AOR-24/AOR-32

may be either surface mounted onto a wall or flush

mounted into a wall.

NOTE:

For flush mounting units,

AOR-24

and

AOR-32

units should be

ordered with the available

AOR-TR32

Flush Mount Trim Ring (sold

separately).

NOTE:

Conduit knockouts exist on the rear, top, and bottom sides of the

enclosure for access to power and communication lines. Determine the
method of bringing in these power and communication lines

before

mounting the enclosure.

NOTE:

Whenever possible, it is best to keep the maximum clearance

possible between analog phone lines and alternating current. Running
phone lines too close to hot VAC lines will produce undesired effects on
the phone line.

9.

For mounting the unit directly to the surface of an interior wall,

10.

The

AOR-24/AOR32

has four (4) surface mounting keyholes. These keyholes

are visible upon product arrival. The first of the two remaining keyholes is
located behind the built in telephone. To remove the built in telephone,

«
...
14
15
16
17
18
...
»

Содержание AOR-16








































Отзывы:

Нет отзывов

Похожие инструкции для AOR-16

Бренд: Yealink Страницы: 2

Бренд: Yealink Страницы: 2

Бренд: Yealink Страницы: 2

Бренд: Yealink Страницы: 2

Yealink SIP-T28P

Бренд: Yealink Страницы: 10

Yealink SIP-T28P

Бренд: Yealink Страницы: 2

Бренд: Yealink Страницы: 4

Yealink SIP-T28P

Бренд: Yealink Страницы: 2

Yealink SIP-T28P

Бренд: Yealink Страницы: 4

Бренд: Yealink Страницы: 158

Бренд: Yealink Страницы: 6

Бренд: Yealink Страницы: 4

Бренд: Yealink Страницы: 16

Бренд: Yealink Страницы: 73

Бренд: Yealink Страницы: 120

Бренд: Yealink Страницы: 2

Бренд: Yealink Страницы: 3

Бренд: Allworx Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды