K11823;6/34
- 6 -
Fig. 4-1 Connection example between camera
and peripheral devices
Co mpu ter
Image processor
Frame grabber
compatible with FC1600FPL
FULL FRAME
ＦＣ １ ６０ ０ ＦＰ Ｌ
S ig nal c abl e
Ｐ ｏ ＣＬ mi ni Ca mer a L in k c ab le
S trob e s ign al
←
E xter nal Sy nc s ign al →
4. How to Operate
(4-1) Connection method
●
Connection
Refer to the connection example between the camera and
peripheral devices (Fig. 4-1).
(1) Remove the cover of the lens attachment section and
attach a lens (option).
(2) The maximum allowable length of a I/O cable is 25 m.
(3) Set the camera operation modes in accordance with the
setting instructions for the operation modes and the shutter
speed that are described in another section.
(4) Connect the digital output connectors on the rear panel of the
camera to the input terminals of the image processing units
(PoCL- compliant frame grabber board, computer, etc.) with
digital cables (option) conforming to PoCL. The maximum
allowable length between the digital output
connector of the camera and the input terminal of said image
processing unit is 10m.
(5) Confirm the connecting condition before turning on the power
switch of the camera.
In 1 or 2 seconds after the power is turned on, the LED operation indicator on the rear panel of the camera changes
from orange to green to show that the camera is in operation.
(Note) The maximum allowable lengths of the camera cable and the digital cable aforementioned are not for the purpose
of guaranteeing the operation of the camera. Proper image signals may not be obtained even when the cables are
within the allowable ranges, depending on the installation conditions of the camera, cables in use and others.
●
Application of test pattern
This equipment has the function of generating test patterns. This test pattern allows the user to confirm the
appropriateness of the connection between the camera and PC as well as the setting of the board to some extent
when used during the initial setup process for the connection with the capture board and others.
<Procedure for switching to test pattern output>
(1) Set the mode switch on the rear of the camera to the position “D” , keeping the power to the camera off.
(2) Turn on the power of the camera while turning and keeping the UP/DOWN switch lever to the upper position (or lower
position).
(3) Return the UP/DOWN switch lever to the neutral position after having heard a buzzer sounding “pip-pip”.
(4) Set the mode switch to the position “2” after confirming that the LED indicator on the rear of the camera is flashing in
orange.
(5) Apply an upward stroke to the UP/DOWN switch lever after confirming that the mode switch is at the position “2”.
(6) Confirm that the buzzer sounds “pip”.
→
Then, the camera start outputting test pattern images.
(7) Turn off the power to the camera.
Since the setting of the test pattern output in the above process is automatically saved, the test pattern will be output when
the power is reapplied from next time.
To shift from the test pattern output mode to the regular camera image output mode, repeat the above steps up until (4) of
<Procedure for switching to test pattern output>, and then apply a downward stroke to the UP/DOWN switch lever at the
step (5).
→
From then on, the camera will output regular image.
Since this setting is saved, it continues to be effective after the power is turned off.
→
Refer to “(4-5) Test pattern display function” for the details of the test pattern.
[Important]
(Note) Make sure to stop supply power from the frame grabber before connecting or disconnecting the camera cable.
If the cable is connected or disconnected while the power is supplied, troubles may be caused.
(Note) Make sure to turn off the camera and connected devices in advance when the camera is connected.
(Note) Make sure to use the frame grabber that confirms to PoCL standard.
This camera is in conformity with PoCL standard Ver.1.2 SafePower.
(Note) When a power supply unit other than Takenaka’s product that are separately sold is used, make sure that it
complies with the following rated specifications:
Power supply voltage:
DC12V±10%
Current capacity: 350mA or over
Take into consideration the fact that inrush current of about 1A flows in when power is applied.
Ripple voltage:
50mVp-p or less (recommended value)
Connector:
3M/SDR-26 FEMALE
(Note) The connector pin assignment is different between PoCL-compliant Camera Link cable and normal Camera Link
cable. Make sure to connect the cable after checking the compatibility of the Camera Link cable in advance.
Carefully note that any failure associated with power application to out-of-specification pins and others is subject to
charged repair.
