background image

Horizontal zone

Alarm signal is issued only
when both horizontal and
downward zone detect objects.

It does not detect small
animals, which are not likely
to reach the height of
horizontal zone.

It does not detect vehicles
moving in the area outside the
range of the downward zone.

Downwar

d zone

Detection distance

Detection distance

Detection distance

(12m)

40’

(12m)

40’

(1m)

3.3’

0

(5m)

16.5’

(10m)

33’

(12m)

40’

[TOP VIEW]

Horizontal

Detection

[SIDE VIEW]

[Wide angle detection]

15º

Variable

Pitch

90º

ADJUST

ABLE:

90º

V

ARIABLE:

180º

(10m)

33’

(10m)

33’

(5m)

16.5’

(5m)

16.5’

0

(12m)

40’

(12m)

40’

Fine Adjustment

[TOP VIEW]

Wall Detection

3” 3”

Masking
unnecessary zones.

Variable
range

Downward Zone

Horizontal Zone

Horizontal Zone

(10m)

33’

(10m)

33’

(5m)

16.5’

(5m)

16.5’

0

(12m)

40’

(12m)

40’

(1m)

3.3’

±90º

±90º

Sensor

Centre

0

(5m)

16.5’

(10m)

33’

(12m)

40’

[SIDE VIEW]

15º

Variable

Pitch

LOWER

SENSOR

COVERAGE

UPPER

SENSOR

COVERAGE

LOWER

SENSOR

COVERAGE

UPPER

SENSOR

COVERAGE

ADJUST

ABLE:

90º

V

ARIABLE:

180º

(10m)

33’

(10m)

33’

(5m)

16.5’

(5m)

16.5’

0

(12m)

40’

(12m)

40’

Fine Adjustment

[TOP VIEW]

Wall Detection

DETECTION
MODE: OR

Fine Adjustment

3” 3”

3” 3”

Masking
unnecessary zones.

Variable
range

Downward zone

(10m)

33’

(10m)

33’

(5m)

16.5’

(5m)

16.5’

0

Detection distance is set by adjusting the angle of downward zone.

Adjusting range 10’(3m) to 40’(12m). [7 ranges]

Detection distance is set by adjusting the angle of downward zone.

Adjusting range 10’(3m) to 40’(12m). [7 ranges]

The detection zone of this unit consists of
horizontal zone and downward zone.
Alarm signal is issued only when both detection
zones detect objects.
Detection distance can be set by adjusting the
angle of downward zone.

MS-12TE is equipped with 1 set of sensor on the
upper side.

MS-12FE is equipped with 2 sets of sensor on the
upper and lower side, making it possible to select
AND mode or OR mode.

Area adjustment

(1) Point the sensor to the centre of the area to be detected.

By turning the sensor up to ±45º, it can detect all 
directions in front of it.
When the unit is turned more than ±45º, detection 
zone will be eliminated one by one from the end.

(2) It consists of seven 

detection zone 
(Wide angle : 90º).

(3) Utilize attached area 

masking sheet when 
eliminating detection zone.

[MS-12TE]

[MS-12FE]

[TOP VIEW]

Horizontal
Detection
X2
UPPER SENSOR
LOWER SENSOR

DETECTION
MODE: OR

Содержание MS-12TE









Отзывы: