Takeuchi TL150 Скачать руководство пользователя страница 63

Страница: 63 / 312

III-20

MACHINE CONFIGURATION

TRAVEL SYSTEM

Removing the Track Roller

1. Loosen the track tension.

2. Loosen the roller installation bolts (1) slightly

(approximately 1 turn).

3. Raise the machine body, take out the installation

bolts (1) and remove the roller (2).

Installing the Track Roller

1. Tighten the roller (2) installation bolts (1) tem-

porarily.

2. Bring the machine body in full contact with the

ground, then tighten the bolts.

Bolt: 241 N·m (track rollers A and B)
Bolt: 156 N·m (track roller C)

Apply thread-locking compound.

3. Raise the machine body, then adjust the track

tension.

Removing the Idler and Track Adjuster

1. Remove the track.

“Removing the Steel Track”

2. Pull out the idler (1).

Idler: 55 kg

3. Pull out the track adjuster

s track spring (2) and

the tensioning cylinder (3).

Track adjuster: 40 kg

Installing the Idler and Track Adjuster

Follow the procedure used for removal in reverse
order.
• Apply grease to the rubbing surfaces of the track

adjuster piston and cylinder.

Содержание TL150

























































































































































































































































































































Результаты поиска

Содержание TL150

Отзывы:

Похожие инструкции для TL150

Бренды по названию

Популярные бренды

Takeuchi TL150, Руководство по ремонту

Результаты поиска

Содержание TL150

Отзывы:

Похожие инструкции для TL150

Бренды по названию

Популярные бренды