Takeuchi TL150 Скачать руководство пользователя страница 309 | Manualshive

Страница: 309 / 312

background image

V-27

TROUBLESHOOTING

BUCKET

1. Is the speed of the bucket cylinders within

the speciﬁed range?

“II. Speciﬁcations, Standards for Judging

Performance”

2. Inspect the pilot valve.

“V-24”

3. Inspect movement of the spool.

“V-25”

4. Perform replacement test for the port relief

valves.

“V-25”

5. Inspect for leaks within the bucket cylin-

ders.

a. Bring the bucket into a level position down

into contact with the ground.

b. Check the left and right bucket cylinders

individually. Disconnect the hose from the
cylinder not being checked and insert a plug
in place of the removed hose.

c. Disconnect two hoses from the cylinder to be

checked and insert plugs into the hoses and
cylinder piping.

d. Raise the lift arms and bring the bucket up

above the surface of the ground. If the front
edge of the bucket falls downward the cylin-
der may be assumed to be at fault. If it does
not fall downward you may assume that there
is a leak within either the control valve or the
self-level valve.

«
...
307
308
309
310
311
...
»

Содержание TL150

























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TL150

Super Boom C185

Бренд: New Holland Страницы: 51

Бренд: jcb Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды