Takeuchi TL150 Скачать руководство пользователя страница 168

Страница: 168 / 312

IV-22

HYDRAULIC UNITS

HST PUMP

16. Install the side cover.

a. Push down the swash plate to mate with the

bearing of the side cover (9).

b. Install the gasket (55) and the side cover (9).

• Install the two bolts (that are longer than

the Allen screws for securing the side cov-
er) temporarily as the positioning guides.

c. Mate the side cover (9) with the housing in-

stallation hole.
• Tap the side cover lightly with a rubber

hammer.

d. Remove the two bolts used as the positioning

guide, and install the six cap screws.
• Tighten the cap screws, starting from the

one at the lower-left corner counterclock-
wise.

• Make sure the swash plate does not in-

terfere with the side cover and the needle
bearing.

Cap Screw: 15~17.5 N·m

17. Install the shaft assembly to the housing.

• Make sure the cylinder block

s hold-down

pin is installed at right angles in the gutter.

18. Install the cover to the shaft spline to protect the

seal carrier.
• Use a plastic sleeve or its equivalent.

19. Assemble the seal carrier.

a. Press-ﬁt the seal (56) into the seal carrier (7).

•  Use a new seal.
•  Apply sealant over the seal perimeter.
  Sealant: Loctite #59231
•  Be  careful  not  to  insert  the  seal  in  the

wrong direction.

• Lubricate the inside of the seal with

grease.

b. Attach the O-ring (8) to the seal carrier (7).

S3F309E

Push

Rubber mallet

S3F308E

Shaft assembly

S3F329E

Protect cover

Содержание TL150

























































































































































































































































































































Результаты поиска

Содержание TL150

Отзывы:

Похожие инструкции для TL150

Бренды по названию

Популярные бренды

Takeuchi TL150, Руководство по ремонту

Результаты поиска

Содержание TL150

Отзывы:

Похожие инструкции для TL150

Бренды по названию

Популярные бренды