Takeuchi TB153FR Скачать руководство пользователя страница 47

Страница: 47 / 239

CONTROLS

Seat and Seat Belt

Seat Belt

CAUTION

Always fasten the seat belt securely
before starting the engine.

Fastening the seat belt
1. Adjust the seat to the optimum position

for operating, raise your torso, and sit back
firmly into the seat.

2. Pull the seat belt to the desired length.

3. Make sure that the belt is not twisted and

then insert the tongue plate (A) into the
buckle (B) of the seat belt until you hear a
clicking sound as it locks in place.

Releasing the seat belt

1. To remove the seat belt, simply press the

button (C) located on the buckle.
The seat belt is automatically stowed
away.

E4B023

E4B024

Содержание TB153FR
















































































































































































































































Результаты поиска

Содержание TB153FR

Отзывы:

Похожие инструкции для TB153FR

Бренды по названию

Популярные бренды

Takeuchi TB153FR, Руководство оператора

Результаты поиска

Содержание TB153FR

Отзывы:

Похожие инструкции для TB153FR

Бренды по названию

Популярные бренды