Takeuchi TB153FR Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 239

background image

88

OPERATION

Operating Procedures

Be Gentle on the Hydraulic Cylinders

Do not extend the hydraulic cylinders to the
stroke ends. Operate them with leeway.

Do not support the machine body with the
hoe attachment as it is lowering with the arm
cylinder fully extended. Doing so
concentrates the load on the arm cylinder
and could damage the arm cylinder.

Do not Drive Piles with the Bucket or Dig
with it Using Shock Force

Doing so will shorten the service life of the
hoe attachment. Use hydraulic force to dig.

Prohibited Operations

WARNING

¡

¡

¡

¡

¡

Do not operate on base rock (hard or
soft).

¡

¡

¡

¡

¡

Do not slew (swing) while traveling. If
you must operate the hoe attachment
while traveling, operate at speeds slow
enough so you have complete control
at all times.

Do not perform breaking or leveling
operations using slew force

Do not break down walls or level ground
using slew force. Also, do not dig the bucket
teeth into the ground during slewing. Doing
so will damage the hoe attachment.

Do not Dig while Traveling

Do not dig the bucket into the ground and
use the traveling force to dig.

E4D029

E4D030

E4D031

E4D032

«
...
88
89
90
91
92
...
»

Содержание TB153FR
















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TB153FR

Бренд: jcb Страницы: 51

Бренд: Komatsu Utility Страницы: 280

Бренд: jcb Страницы: 51

Бренд: Galeo Страницы: 299

Бренд: MERLO Страницы: 232

Бренд: RAMROD Страницы: 34

Бренд: ITech Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды