Takeuchi TB153FR Скачать руководство пользователя страница 44

Страница: 44 / 239

CONTROLS

Doors and Covers

Fuel Filler Cap

WARNING

Do not smoke or permit open flames
while fueling or near fueling
operations.

Supply fuel in a well ventilated place
and with the engine stopped.

Clean up spilled fuel immediately.

Do not fill the fuel tank to capacity.
Allow room for expansion.

Tighten the fuel filler cap securely.

Opening
1. Open the key cover, insert and turn the

key counterclockwise to unlock the fuel
cap.

2. Turn the fuel cap counterclockwise and

remove it.

Closing
1. Set the fuel cap in place and turn it

clockwise.

2. Turn the key clockwise to lock the fuel cap,

then remove the key.

Содержание TB153FR
















































































































































































































































Результаты поиска

Содержание TB153FR

Отзывы:

Похожие инструкции для TB153FR

Бренды по названию

Популярные бренды

Takeuchi TB153FR, Руководство оператора

Результаты поиска

Содержание TB153FR

Отзывы:

Похожие инструкции для TB153FR

Бренды по названию

Популярные бренды