Takeuchi TB153 FR Скачать руководство пользователя страница 80

Страница: 80 / 239

OPERATION

(1) Offset the boom to the front of the

operator’s seat and move the boom near
the cab.
Offset the boom to the right and move
the bucket near the cab.

(2) Offset the boom fully to the right and

check that it can be set to the maximum
rear inclination.

(3) Offset to the left in the posture in (2)

above

Operation when the boom has stopped
automatically
1. If the boom has stopped while rising:

Operate the boom downward.

2. If the boom has stopped while offsetting

to the left:
a. Operate the boom downward to move

it outside the automatic stop range.

b. Offset to the left.

Offsetting to the right is possible
regardless of the boom’s posture.

L2D009

L2D010

Machine Operation

Содержание TB153 FR
















































































































































































































































Результаты поиска

Содержание TB153 FR

Отзывы:

Похожие инструкции для TB153 FR

Бренды по названию

Популярные бренды

Takeuchi TB153 FR, Руководство оператора

Результаты поиска

Содержание TB153 FR

Отзывы:

Похожие инструкции для TB153 FR

Бренды по названию

Популярные бренды