Takeuchi TB153 FR Скачать руководство пользователя страница 42

Страница: 42 / 239

CONTROLS

Lower Front Window (Cab)

Removing

1. Open the front window and stow it in the

ceiling.

2. Grasp the protruding parts (4) on the left

and right with your fingers and slowly lift
the lower front window off.

3. Hold the glass firmly, place the lower front

window through the guides (5) at the rear,
then set it on the supports (6) and fasten
it in place.

C4C006

Doors and Covers

Side Window (Cab)

1. Grasp the catch (7), unlock it and open

the side window.

2. To close the side window, close it until a

click is heard.

Tool Case

Lock and unlock
1. Insert and turn the starter key

counterclockwise (clockwise) to unlock
(lock).

N0B008

N0B023

Содержание TB153 FR
















































































































































































































































Результаты поиска

Содержание TB153 FR

Отзывы:

Похожие инструкции для TB153 FR

Бренды по названию

Популярные бренды

Takeuchi TB153 FR, Руководство оператора

Результаты поиска

Содержание TB153 FR

Отзывы:

Похожие инструкции для TB153 FR

Бренды по названию

Популярные бренды