Takeuchi TB153 FR Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 239

background image

38

CONTROLS

Doors and Covers

Starter Key

The starter key is used not only to start and
stop the engine, but also to lock and unlock
the following places :

¡

Cab door

¡

Fuel filler cap

¡

Rear cover

¡

Rear cover

¡

Tool box

¡

Manual storage compartment (Canopy)

Cab Door

WARNING

When mounting and dismounting the
cab, first open the door fully to the locked
position and check that it does not move.

Open the door fully and press it against the
catch at the back of the door to lock it in place.
Always lock the door when mounting and
dismounting and when operating the
machine.

Lock and unlock

1. Insert and turn the starter key.

Opening
1. Pull the knob (1) towards you and open

the door.
To open the door from inside the cab, push
the lever (2) to the front.

2. Open the door fully and press it against

the cab to lock it in place.

Closing

1. Either push release lever (3) to the front

or lower release lever (4).

2. Close the released door.

E4B003

C4C001

2

1

4

3

C4C002

«
...
38
39
40
41
42
...
»

Содержание TB153 FR
















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TB153 FR

Бренд: Komatsu Страницы: 261

Бренд: RAMROD Страницы: 36

Бренд: New Holland Страницы: 51

Бренд: Daewoo Страницы: 656

Бренд: jcb Страницы: 24

Бренд: Yuchai Страницы: 157

Бренд: Glasdon Страницы: 13

Бренд: Komatsu Страницы: 51

Бренд: Komatsu Страницы: 31

Бренд: KitchenAid Страницы: 39

Бренд: jcb Страницы: 31

Бренд: ICC Страницы: 37

Бренд: Barko Страницы: 99

Бренд: Hyundai Страницы: 41

Бренд: Wacker Neuson Страницы: 29

Бренд: Terex Страницы: 87

Бренд: Terex Страницы: 114

Бренд: Gravely Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды