Tait TM8100 mobiles Скачать руководство пользователя

Страница: 72 / 76

CCR

TM8100/TM8200 Computer-Controlled Data Interface (CCDI) Protocol Manual

April 2007

2.9

Unsolicited Messages from the Radio

2.9.1

Summary and Examples

The following messages may be returned to the DTE without user
intervention.

Examples:

V0612345-18

Sequence 12345 detected

V065E5E5-EE

Sequence 55555 detected (E is repeat tone in this case)

M01P02

Transmit timeout warning (10s before inhibit)

M01R00

CCR mode entered

2.9.2

PTT exceeds max transmit limit

Description

The radio uses this response to advise the control head that PTT is about to
timeout.

For control heads with user interfaces, the warning threshold is the duration
timer configured for the network minus 10s.

Response

Msspcc

Where:

Effect

Whenever the radio reaches its maximum transmit period the radio will
inform the control head. After a further short delay the radio will turn off
the transmitter.

Message

Cmd

Function

Vssx...xcc

Selcall decode sequence

Msspcc

Ptt exceeds max transmit limit

Mssrcc

CCR initialised

Parameter

Value

ASCII letter M denotes the message

ASCII hex number ss is the number of parameters (always “01”)

ASCII letter P denotes a PTT being applied that has exceeded the
default transmit timer warning threshold

ASCII hex number cc is the checksum

Содержание TM8100 mobiles













































































Результаты поиска

Содержание TM8100 mobiles

Отзывы:

Похожие инструкции для TM8100 mobiles

Бренды по названию

Популярные бренды

Tait TM8100 mobiles, Руководство по протоколу

Результаты поиска

Содержание TM8100 mobiles

Отзывы:

Похожие инструкции для TM8100 mobiles

Бренды по названию

Популярные бренды