Tait TM8100 mobiles Скачать руководство пользователя

Страница: 22 / 76

CCDI

TM8100/TM8200 Computer-Controlled Data Interface (CCDI) Protocol Manual

April 2007

1.9

Commands to the Radio

The following commands are available to send from the PC to control the
radio.

In all cases, if a command is received without error by the radio and all
parameters are valid, the command is executed.

The prompt character ‘.’ is returned to the PC immediately after receiving a
command, to signify that another may begin. If an error arises, the PC is
notified with an appropriate ERROR response.

1.9.1

CANCEL

The CANCEL command tells the PC to abort the current action that the
radio is performing.

Format

c [SIZE] [CANCEL_TYPE] [CHECKSUM]

Command

Character

Function

Valid in Mode

Mode radio must be
in or switch to, to act
upon the message
(TM8200 only)

CANCEL

Cancel current activities

Conventional

DIAL

Initiate a conventional
call

Trunked
Conventional

Conventional

FUNCTION

Implement RU function

Trunked
Conventional

Dependent on function

GO_TO_CHANNEL

Tune to conventional
channel

Trunked
Conventional

Conventional

QUERY

Query RU Model, data
parameters, software
versions, etc. Query
SDM.

Trunked
Conventional

Either, no change
required

SEND_ADAPTABLE_SDM

Send conventional SDM
with SFI/GFI field
formatting

Trunked
Conventional

Conventional

SEND_SDM

Send conventional SDM

Trunked
Conventional

Conventional

TDMA

Configure and open
TDMA channel
Queue TDMA data for
sending
Close TDMA channel

Conventional

TRANSPARENT (FFSK and
THSD)

Switch to Transparent
mode (FFSK or THSD)

Conventional
Trunked

Conventional

Содержание TM8100 mobiles













































































Результаты поиска

Содержание TM8100 mobiles

Отзывы:

Похожие инструкции для TM8100 mobiles

Бренды по названию

Популярные бренды

Tait TM8100 mobiles, Руководство по протоколу

Результаты поиска

Содержание TM8100 mobiles

Отзывы:

Похожие инструкции для TM8100 mobiles

Бренды по названию

Популярные бренды