Tait TB9400 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 49

Tait TB9400 Скачать руководство пользователя страница 27

TB9400 Specifications Manual

Base Station Specifications

27

© Tait Limited July 2017

Duty cycle

Up to 3600m (11810ft) altitude

Above 3600m (11810ft) altitude

100% at maximum rated output power

d

at +60°C

(+140°F) ambient temperature
100% at maximum rated output power

d

at +50°C

(+122°F) ambient temperature, or output power
derated by 1.5dB at +60°C (+140°F)

d. Measured directly on PA output.

Mismatch capability

Ruggedness

Stability

open and short circuit load at any phase angle for one
hour

e

5:1 load VSWR at all phase angles

e

e. Under power foldback.

Protection

f

Temperature

Current

Supply voltage

VSWR

Feedback loop instability

power foldback to 35W if RF power devices exceed
safe operating conditions

power foldback and shutdown if RF power devices
exceed safe operating currents for more than 5
seconds

power foldback to 35W when supply voltage is 24V to
26V and 30V to 32V; shutdown when supply voltage
is <24V and >32V

power foldback to 35W when VSWR >3:1

power reduces to maintain loop stability within safe
margins

f. Power foldback to 35W occurs only if the output power is set to more than 35W. If the output power is set to less than

35W, the power stays at the set level during foldback conditions.

Adjacent channel power

g

All modulation types

< –67dBc TIA-102.CAAA and TIA-102.CCAA

Adjacent channel power (B3 and H bands only)

All modulation types

< –60dBc EN 300 113

g. 762-776MHz band complies with FCC 47 CFR 27.53(e)(6) and 47 CFR 90.543(a)

Modulation emission spectrum

TIA-102.CAAB-D paragraphs 3.2.5.1 and 3.2.5.2,
LSM, and TIA-102.CCAB paragraph 3.2.5.1

Modulation fidelity

<2% TIA-102.CAAA and TIA-102.CCAA

Intermodulation

better than 65dB TIA-102.CAAA and TIA-102.CCAA
(typical)

General (Continued)

«
...
25
26
27
28
29
...
»

Содержание TB9400


















































Отзывы:

Нет отзывов