Tait TB9400 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 49

Tait TB9400 Скачать руководство пользователя страница 13

TB9400 Specifications Manual

Base Station Specifications

13

© Tait Limited July 2017

DC Input

Input voltage

User-programmable alarms

a

Low battery voltage
High battery voltage

User-programmable limits

b

Startup voltage
(after shutdown)
Shutdown voltage

Battery protection (fail-safe) limits

c

Startup voltage
Undervoltage shutdown
Overvoltage shutdown
Overvoltage shutdown reset

12V PMU

10V to 14V
14V to 17.5V

10.9V to 15V ±0.3V

10V to 13.5V ±0.3V

10.8V ±0.2V
9.5V ±0.3V
18.1V ±0.3V
17.1V ±0.3V

24V PMU

20V to 28V
28V to 35V

21.8V to 30V ±0.5V

20V to 27V ±0.5V

21.6V ±0.5V
19V ±0.5V
36.2V ±0.5V
34.2V ±0.5V

48V PMU

40V to 56V
56V to 70V

43.6V to 60V ±1V

40V to 54V ±1V

43.2V ±1V
38V ±1V
72.4V ±1V
68.4V ±1V

a. User-programmable alarms can be set for low or high battery voltage, using the web interface. The alarms will be triggered

when the set voltage levels are reached. These limits are subject to the tolerances of the battery protection circuitry, as
stated in “Battery Protection (Fail-safe) Limits” above.

b. The user-programmable startup and shutdown limits allow for adjustable startup and shutdown voltages. Using the web

interface, these limits can be adjusted for different numbers of battery cells, or for the particular requirements of the base
station operation. Once the limits are reached, the PMU will shutdown. These limits are subject to the tolerances of the
battery protection circuitry.

c. The battery protection limits are set in hardware at the factory and cannot be adjusted by the user. These limits will not be

reached under normal operation conditions, but are provided as “fail-safe” measures to protect the battery from deep
discharge.

Input current

0V to battery protection startup
voltage

d

Battery protection startup voltage to
user-programmed startup voltage

e

12V

2mA maximum

40mA typical
at 10.8V

24V

2mA maximum

30.1mA typical
at 21.6V

48V

1.2mA maximum

13.2mA typical
at 43.2V

Operating current

refer to

“Power and Current Consumption” on page 15

d. When the input voltage drops below the battery protection undervoltage shutdown limit, and until the voltage rises above the

battery protection startup voltage.

e. At initial power-up; or, after battery protection has occurred, when the input voltage rises above the battery protection startup

voltage (PMU now under control of its microcontroller), but is still below the user-programmed startup voltage

Protection

Fault current (input)
Wrong input voltage
Wrong input voltage polarity

circuit breaker or fuse in external wiring

f

electronic lock-out
shunt diode

f. Provided by user.

General

Efficiency at rated output

12VDC
24VDC
48VDC

82%
85%
90%

«
...
11
12
13
14
15
...
»

Содержание TB9400


















































Отзывы:

Нет отзывов