Taiden HCS-5300BAT Скачать руководство пользователя страница 103

Страница: 103 / 117

7.2 Digital infrared wireless main unit

Fault

Analysis

Solution

Cannot startup.

No power supply or no power cord

connected to main unit.

Connect the power supply with the power

cord.

7.3 Charging Unit

Fault

Analysis

Solution

The power indicating light is

not on when the unit is

powered on.

The power cord is not plugged into the

power socket.

Plug the power cord into the power

socket and supply power to the charging

unit.

The fuse has blown.

Change the fuse.

Please contact the local TAIDEN service

center.

The charging indicating light of

the charging lattice is not

lighting up though the battery

is plugged-in.

The battery is not properly plugged-in.

Plug-in the battery properly into the

charging lattice.

The charging contact is covered by

dust.

Please clean the charging contact with

dry cotton swab.

Battery working time is short.

Lithium-Ion battery deteriorated.

Please replace with new HCS-5300BAT

Lithium-Ion battery.

Содержание HCS-5300BAT






















































































































Результаты поиска

Содержание HCS-5300BAT

Отзывы:

Бренды по названию

Популярные бренды

Taiden HCS-5300BAT, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HCS-5300BAT

Отзывы:

Бренды по названию

Популярные бренды