Taege RC350 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 11

Taege RC350 Скачать руководство пользователя страница 11

11

07/11/2016

A Ground Breaking Company Since 1923

Warning Screens

Kg/ha Warning

kg/ha has a restriction on the maximum weight at 500kg/ha and minimum of 0.1 kg.ha.

Speed Warning

The machine will not operate under 0.010 kph and will warn when 15kph is exceeded.

The controller warns if calibration weight or sample counts are outside recommended
settings.

Additional Configuration

Additional configuration settings are available when the RC350 Controller is replaced or
moved to another application and should only be accessed when a Dealer or Taege technical
person has been contacted.

Disclaimer

The information in these instruction sheets may or may not apply to your controller.

In using this information, you acknowledge that such information and materials may contain
inaccuracies or errors and we expressly exclude liability for any such inaccuracies or errors
to the fullest extent permitted by law.

Please contact your Taege Dealer or Taege Technical Personal after identifying your
machine and controller for further information.

Warning

Do not weld on your machine unless you have disconnected the
tractor 12vdc power source and on an Air Seeder, the motor/s
connector plugs.

«
...
9
10
11

Содержание RC350












Отзывы:

Нет отзывов