background image

19

IMPORTANT WARNINGS AND PRECAUTIONS

  NEVER

 allow water or moisture to make contact with the electronic 

components inside the transmitter, receiver, servos, switch harness, 
etc.! This could lead to failure or improper functionality of components 
and poor control of aircraft which could pose a safety hazard.

  NEVER

 operate R/C model aircraft near power lines, radio or cell phone towers, 

roads or automobiles, buildings, or pedestrians. Be very careful in locations 
where many R/C aircraft are being used simultaneously.

  NEVER

 operate R/C equipment if you are physically impaired as it could pose a 

safety hazard to yourself or others in the area.

  NEVER

 allow small children to operate/control model R/C equipment without the 

supervision of an adult.

  NEVER

 allow the transmitter’s throttle stick to accidentally be moved away from 

the “off” or minimum position while the model’s engine/motor is moving.

  ALWAYS

 range check the radio system before use.

  ALWAYS

 make sure that all transmitter stick movements operate all servos 

properly in the model. Check the proper operation of control surfaces before and 
after starting the engine/motor.

  ALWAYS

 make sure the transmitter antenna is unfolded entirely so that it’s 

pointing upright to ensure max. range and control of the aircraft.

  

Do not store your radio equipment in extremely hot or cold locations, in direct 
sunlight, or in locations with high humidity. Store R/C equipment in cool and 
dry locations.

  

Do not allow chemicals to come in contact with any parts of the radio system. 
Substances such as glow fuel, gasoline, CA glue, etc. could permanently damage 
plastic parts of the radio system.

  

If NiCd batteries were installed in the transmitter, remove the batteries before 
placing the radio in long-term storage.

Содержание TTX600

























Отзывы: