PAGE
Section 5 • System Set-up
Section 5 • System Setup
5.44 IR Flood Emitter Connections
When two or three S4.3 Controllers are
used in the same system, we recommend
that you connect them so that only one IR
“flood” emitter works. This avoids potential
interference that may lead to erratic
operation.
Use the following connection guide for
multiple S4.3 Controller systems:
a) For 5-8 zone systems (two S4.3
Controllers):
•
Remove the jumper between terminals 2
and 3 of the TX FORMAT block on S4.3
Controller “A” but leave the jumper in
place on S4.3 Controller “B”.
•
Connect terminal 3 of S4.3 Controller A’s TX
FORMAT block to terminal 4 on S4.3
Controller “B”.
This completes the signal link to the IR
“flood” emitter on S4.3 Controller “B”.
TX-FORMAT
1 2 3 4 5 6
TX-FORMAT
1 2 3 4 5 6
Use this jumper arrangement in a system with 2 Super
Controllers to disable the flood IR emitters on the first
controller and enable the emitter on the second.
Super Controller
"A"
Super Controller
"B"
b) For 9-12 zone systems (3 S4.3
Controllers):
• Remove the jumpers between terminals 2
and 3 of the bottom two S4.3 Controller’s
TX FORM blocks (S4.3 Controller “A” and
“B”) but leave the jumper in place on
S4.3 Controller “C”.
• Connect terminal 3 of the S4.3 Controller
“A” TX FORM block to terminal 4 on S4.3
Controller “B”.
• Connect terminal 3 of the S4.3 Controller
“B” TX FORM block to terminal 4 on S4.3
Controller “C”.
This completes the signal link to the IR
“flood” emitter on S4.3 Controller “C”.
5.43 Source Connections
Connect all sources to the first S4.3
Controller (“A“) in accordance with the
instructions in Section 4.11. Connect
Source 1’s “loop through” outputs on S4.3
Controller “A” to the corresponding Source
1 inputs on S4.3 Controller “B“ using
shielded PHONO to PHONO cables. Follow
this procedure for all inputs.
The loop “OUT“ for each of the sources on
the last controller in the chain can be
connected to the main system amplifier's
inputs if required.
If a system requires a third S4.3 Controller,
simply repeat this procedure but connect
source outputs on S4.3 Controller “B” to
the corresponding inputs on S4.3
Controller “C”.
NOTE: It is particularly important to
observe proper channel continuity when
connecting source components to more
than one S4.3 Controller. Once again, BE
PATIENT AND BE CAREFUL.
OUTPUT
RIGHT
LEFT
4
3
2
AUDIO IN
AUDIO
OUT
IN
RIGHT
INPUTS
LEFT
OUT
IN
OUT
IN
OUT
IN
OUT
SPEAKERS
RIGHT
LEFT
DATA
1
ZONE D
S4.3 MUTI-RO
CONTROL
LINK
IN
OUT
230V AC
50Hz
POWER CONSUMPTION: 430W MAX
PRE/LINE-OUT
TRIGGER
PAGING
AC OUTLET
230V 50Hz
SWITCHED TOTAL:
460W MAX
1 2 3 4 5 6
Super Controller "B"
Super Controller "A"
Source component
4
3
2
AUDIO IN
AUDIO
OUT
IN
RIGHT
INPUTS
LEFT
OUT
IN
OUT
IN
OUT
IN
OUT
SPEAKERS
RIGHT
LEFT
DATA
1
ZONE D
S4.3 MUTI-RO
CONTROL
LINK
IN
OUT
230V AC
50Hz
POWER CONSUMPTION: 430W MAX
PRE/LINE-OUT
TRIGGER
PAGING
AC OUTLET
230V 50Hz
SWITCHED TOTAL:
460W MAX
1 2 3 4 5 6
26
Содержание S4.3
Страница 1: ...MULTI ROOM SYSTEM S4 3 S4 3 MULTI ROOM SYSTEM I n s t a l l a t i o n M a n u a l...
Страница 43: ...PAGE 40...
