background image

Product description |

5

2.2.10

Section defrosting

The need for section defrosting is depending on the humidity in the extract air and the outdoor air temperature. The
general function is to defrost one section at the time with the warm extract air.

If more heating is required the integrated control module regulate the by-pass damper and the exchanger dampers to-
wards increased energy recovery.

When differential pressure increases over set value a defrosting cycle is activated. A signal from the control module ini-
tiate the dampers to close in sequence. If the exhaust temperature drops below set value the control module will regu-
late the by-pass damper and exchanger dampers towards decreased energy recovery.

When differential pressure decrease below set value, the defrosting cycle will be deactivated. If differential pressure in-
crease over max value when defrosting is active, fan stop defrosting will start. After stop defrosting the unit will re-
start. If the pressure does not decrease, the air handling unit is stopped and an alarm is shown in the display. Make sure
that the ice is melted before restarting the unit.

A

D

B

1

A

D

S

3

A

D

S

2

A

D

S

1

DM50-C

P

ACCESS

T

EHS

PDT3

1

2

3

4

DM50–C

Control module

ADB1

By-pass damper

ADS1-3

Exchanger dampers

PDT3

Differential pressure sensor

EHS

Exhaust temperature sensor

1 = Outdoor, 2 = Extract, 3 = Exhaust, 4 = Supply

Section defosting settings in NaviPad

Log in with service mode using password 0612.

Temperature in the exhaust air can be adjusted. Use the navigation path “Data & Settings > Temperature control > Ex-
changer > Defrosting 3”.

Data & settings > ... > Exchanger > Defrosting 3

19 Dec 10:21 PM

Setpoint min limit

4 °C

Max limit pressure

150 %

Units are delivered with stop defrosting activated. Use navigation path “Configuration > Function > Temperature control
> Defrosting 3” to inactivate.

Configuration > Functions > Temperature control

19 Dec 10:21 PM

Defrosting 3

>

Configuration > ...> Temperature control > Defrosting 3

19 Dec 10:21 PM

Max limit pressure start fan stop defrosting

Yes

154394 | A001

Содержание Topvex SX/C





















Отзывы: