background image

DVV 16.08.2021 

23 

The Manufacturer

Systemair d.o.o. 

Špelina 2

, SI-2000 Maribor 

Tel.: +386 2 4601 801 

Certifies herewith that the following products

Thermo roof fan, type 

 

DVV/DVVI-XS, XM, XL, XP/120 
DVV-T

ensure all relevant requirements of following directives

EC Machinery Directive (2006/42/EC) 
Electromagnetic compatibility directive (2014/30/EU) 
Low Voltage Directive (2014/35/EU) 
Regulation (EU) No 305/2011 (CPR) 
Commission Regulation (EU) No 2019/1781 (Ecodesign) 
Commission Regulation (EU) No 327/2011 (Fans) 
Commission Regulation (EU) No 1253/2014 

Applied harmonized standards, in particular:

 

EN ISO 12100

 

Safety of machinery - General principles for design - Risk assessment and risk reduction 

EN ISO 13857 

Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower 
limbs  

EN 60204-1 

Safety of machinery - Electrical equipment of machines - Part 1: General requirements 

Note1

: Compliance with EC Machinery Directive and EN ISO 13857 refers to the mounted protective guards on the 

inlet of the fan, as far they are in the extent of delivery. For the fully accordance with mentioned requirements (pro-
tective guards or safety assurance in other way) the performer is responsible.

 

Note2

: Compliance with EMC Directive 2014/30/EC only relates to this product if it has been connected directly to the 

customary electricity mains. If this product is integrated into a system or completed and operated with other compo-
nents (e.g. regulation and control appliances), the manufacturer or operator of the overall system is responsible for 
compliance with EMC Directive 2014/30/EC.

 

Maribor,

 

16.08.2021

 

Date 

Anton Zupančič

, Director 

E

U

 

 Declaration of Conformity 

Содержание DVV-XL


























Отзывы: