background image

THREE-YEAR LIMITED WARRANTY

System Sensor warrants its enclosed smoke detector to be free from defects in
materials and workmanship under normal use and service for a period of three
years from date of manufacture. System Sensor makes no other express
warranty for this smoke detector.

No agent, representative, dealer, or employee of the Company has the
authority to increase or alter the obligations or limitations of this Warranty.
The Company’s obligation of this Warranty shall be limited to the repair or
replacement of any part of the smoke detector which is found to be defective
in materials or workmanship under normal use and service during the three
year period commencing with the date of manufacture.

After phoning System Sensor’s toll free number 800- SENSOR2 (736- 7672)
for a Return Authorization number, send defective units postage prepaid to:
Honeywell, 12220 Rojas Drive, Suite 700, El Paso TX 79936, USA. Please
include a note describing the malfunction and suspected cause of failure. The
Company shall not be obligated to repair or replace units which are found to
be defective because of damage, unreasonable use, modifications, or
alterations occurring after the date of manufacture. In no case shall the
Company be liable for any consequential or incidental damages for breach of
this or any other Warranty, expressed or implied whatsoever, even if the loss
or damage is caused by the Company’s negligence or fault. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you. This Warranty gives
you specific legal rights, and you may also have other rights which vary from
state to state.

16

E56-6965-000

©2020 System Sensor. 10/28/2020

System Sensor® is a registered trademark of Honeywell International Inc.

Содержание OSI-RIE Series

















Отзывы: