SYSMEX CyFlow Cube 8 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 43

background image

Instrument Operating Manual

CyFlow® Cube 8 Rev-27_2015-07-02

Sysmex Partec GmbH

Am Flugplatz 13, 02828 Görlitz, Germany · Phone +49 3581 8746-0 · Fax +49 3581 8746-70 · [email protected] ·

www.sysmex-partec.com

22 / 43

5.

CyView

TM

Instrument/Measurement Settings

Prime/Work/Clean

There are 3 different possible modes available: The “PRIME” mode for a
priming/initialization process, the

“WORK” mode for measurements and the “CLEAN”

mode for cleaning of the system.

Prime, Work and Clean mode

5.1

Priming / Initialization process

There is a PRIME mode available as a Start Up process for the CUBE instrument. This
process includes cleaning, filling the tubes with sheath fluid and control of the instrument
set up. If a new original CFG-file will be loaded the PRIME mode is always selected. User
defined configuration files can start in PRIME or WORK mode, depend on the status
during saving.

In the following cases the PRIME mode should be performed:



Starting the instrument for the first time

→

Daily initialization



After the sheath fluid bottle was filled



As trouble-shooting procedure (no/bad signals, blocking, etc.)

To start the priming/initialization process, please follow the instructions below:



Open a configuration file and select the initialization modus by clicking on the

Initialization batch symbol (Sysmex Partec Master Cfg-file: Prime mode is pre-set).

If you will perform the daily check-

up please select the “Calibration Beads”

configuration-file. Only in this configuration file you will find the correct settings for
the calibration beads. These settings are crucial for a correct verification of the
instrument performance.

Initialization batch, Work batch and Clean batch

«
...
20
21
22
23
24
...
»

Содержание CyFlow Cube 8












































Отзывы:

Нет отзывов

Похожие инструкции для CyFlow Cube 8

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: Balanced Body Страницы: 4

Бренд: KaVo Страницы: 13

Бренд: vc999 Страницы: 52

D-IMager EKL3104

Бренд: Panasonic Страницы: 13

Бренд: Labokey Страницы: 5

Бренд: E-Z Trail Страницы: 8

Бренд: B&K Страницы: 10

AJSPD850P - P2 DECK

Бренд: Panasonic Страницы: 73

Бренд: XanLite Страницы: 4

Бренд: MAGIC FX Страницы: 25

Бренд: NARGESA Страницы: 37

Бренд: NARGESA Страницы: 6

Бренд: quadient Страницы: 188

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды