Synapse SNAPconnect E12 Скачать руководство пользователя | Manualshive

Страница: 32 / 35

background image

28

SNAPconnect E12 User Guide — 116-081614-030-B001

Regulatory Information and Certifications

RF Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance of 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Certifications and Regulatory Information (USA Only)

FCC Part 15 Class B

These devices comply with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) These
devices may not cause harmful interference, and (2) These devices must accept any interference received, including
interference that may cause harmful operation.

Radio Frequency Interference (RFI) (FCC 15.105)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or
relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the
equipment into an outlet on a circuit different from that of the receiver. Consult the dealer or an experienced radio/TV
technician for help.

If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

l

Reorient or relocate the receiving antenna.

l

Increase the separation between the equipment and receiver.

l

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

l

Consult the dealer or an experienced radio/TV technician for help.

Labeling Requirements (FCC 15.19)

This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

«
...
30
31
32
33
34
...
»

Содержание SNAPconnect E12




































Отзывы:

Нет отзывов

Похожие инструкции для SNAPconnect E12

Бренд: ADTRAN Страницы: 5

Бренд: EchoLife Страницы: 16

WisLink-LoRa RAK2247 SPI/USB

Бренд: RAKwireless Страницы: 19

NETcon D-G-64NE

Бренд: ZIEHL-ABEGG Страницы: 27

Бренд: Abocom Страницы: 2

OFFICE CONNECT CABLE/DSL SECURE GATEWAY...

Бренд: 3Com Страницы: 102

Бренд: SAGEMCOM Страницы: 60

Бренд: NETGEAR Страницы: 10

Бренд: SiboTech Страницы: 39

Бренд: ATX Страницы: 84

Бренд: ZyXEL Communications Страницы: 20

Бренд: Afar Страницы: 75

Бренд: Coalesenses Страницы: 30

Бренд: Watchguard Страницы: 26

Бренд: ZyXEL Communications Страницы: 2

Бренд: Black Box Страницы: 3

Бренд: AWB Страницы: 59

Бренд: OBLO Living Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды